DOW-UAP-D147 — AAWSAP DIRD, Ultracapacitors as Energy and Power Storage Devices, November 2010
File DOW-UAP-D147 is a declassified pdf from Department of War, recording an incident dated 11/1/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.
- File
- DOW-UAP-D147
- Agency
- Department of War
- Incident date
- 11/1/10
- Location
- Las Vegas, Nevada
- Released in
- Release 06 (2026-09-18)
- File type
Topics: AAWSAP & DIRDs
This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.
This DIRD surveys ultracapacitors as high-power energy-storage devices and argues that their main value lies in extremely rapid charge and discharge, very long cycle life, and usefulness in systems that need short bursts of power rather than sustained energy delivery. The report explains how ultracapacitors differ from batteries, reviews the materials and cell designs that determine their performance, and emphasizes that they are especially useful for power stabilization, backup power, load leveling, regenerative braking, and other applications where fast energy transfer matters more than total stored energy. It also notes their drawbacks, including lower energy density, self-discharge, and voltage-management requirements that limit their usefulness as stand-alone replacements for batteries in many applications. The document presents ultracapacitors as a maturing and increasingly important technology whose most credible aerospace and military uses lie in pulsed-power, missile and munitions systems, electric propulsion support, and other hybrid power architectures rather than in long-duration primary energy storage.
Open original file · WAR.GOV page
TL;DR
The only thing faster than the charge rate is the filing date.
- DIRD D147, DoW, Nov 2010, Las Vegas
- Surveys ultracapacitor tech for fast-burst power in aerospace/military
- No official conclusion in the file
AI summary
A Defense Intelligence Reference Document titled "Ultracapacitors as Energy and Power Storage Devices," prepared by the Defense Warning Office's Technology Warning Division, was published in November 2010. The document covers ultracapacitor technology, applications, and recent developments, with authors AAP Person 84 and AAP Person 85. It details the operation, materials, and performance of ultracapacitors, including electrode types, electrolytes, and comparisons with batteries. The text focuses on energy storage devices, discussing materials like activated carbon, carbon nanotubes, graphene, and carbide-derived carbons, as well as applications in electronics, transportation, aerospace, and military systems. It mentions research by companies such as Lockheed Martin and Northern Lights Semiconductor Corp., and outlines advancements in electrode design, electrolytes, and manufacturing. The document includes endnotes and references citing academic papers and technical reports from 2004 to 2010.
Full text
Page 1
UNCLASSIFIED//F8R 8ffl@I.tltt tJ!I!! eHt I
Defense
Intelligence
Reference
Document
Defense Futures
01 November 2010
!COD : 20 July 2010
DI A-08- 1011 -005
Ultracapacitors as Energy and
Power Storage Devices for
Commercial and Military
Applications
UNCLASSIFIED/f FQA &FFI&Iat.k ll6E 8Ptl¥
Page 2
UNCLASSIFIED//F8R 8Ff!C!Jlct tt:!!! tJHL I
Ultracapacitors as Energy and Power Storage Devices for
Commercial and Military Applications
The Defense Intelligence Reference Document provides nonsubstantive but
authoritative reference information related to intelli ence to ics or methodolo ies.
Prepared by:
Technology Warning Division (DW0-4)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
Authors:
AAP Person 84, AAP Person 85
(U) COPYRIGHT WARNING: Further dissemination of the photographs in this publication is not authorized.
This product is one of a series of advanced technology reports produced in FY 2010 under the
Defense Intelligence Agency, Defense Warning Office's Advanced Aerospace Weapons System
Applications (AAWSA) Program. Comments or questions pertaining to this document should be
addressed to !MP Person 1
AAWSA Program Manager, Defense Intelligence Agency,
ATTN: JUIAF - DI/DWO-3, Bldg 6000, Washington D.C. 20340-5100
I
UNCLASSIFIED,<fiOA OFFI&l..tJk WSE e••tv
Page 3
UNCLASSIFIED1fFOR 8ffl@IAL tt9! e"t I
Contents
Summary................................................................................................................iv
Chapter 1: Concept Overview ................................................................................ 1
Batteries and Ultracaps ...................................................................................... 3
History ............................................................................................................... 5
Chapter 2: Materials Technology ........................................................................... 8
Electrolytes ........................................................................................................ 8
Electrodes ............................................................................................................................................................................ 9
Chapter 3: Applications ....................................................................................... 13
Electronics and Telecommunications ................................................................ 13
Industrial ......................................................................................................... 13
Transportation ................................................................................................. 14
Aerospace ........................................................................................................ 15
Chapter 4: Recent Developments ........................................................................ 17
CNTs and Advanced Carbons ............................................................................ 17
Thin Films ........................................................................................................ 20
Magnetic Capacitors ......................................................................................... 21
Chapter 5: Future Developments ......................................................................... 25
Chapter 6: Conclusions ........................................................................................ 27
Chapter 7: Endnotes ............................................................................................ 28
Figures
Figure 1. Ultracaps in Various Configurations . ...................................................... 1
Figure 2. Operation of an Ultracapacitor................................................................3
Figure 3. Ragone Plot.............................................................................................5
Figure 4. Electrolytic Capacitor as Designed and Patented by SOHIO.....................5
Figure 5. Activated Carbon Porosity..................................................................... 10
Figure 6. Ultracapacitor Use in a Forklift................................................................14
Figure 7. CNT Forest................................................................................................18
Figure 8. Transmission Electron Microscope Image of Graphene ......................... 19
Figure 9. Relationship Between Average Pore Size and Normalized Specific
Capacitance ............................................................................................................. 20
ii
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Page 4
UNCLASSIFIED11FOR. 8FFl@IAL tt.!! e"t I
Figure 10. CDC Synthesis and Electrochemical Test Cell Preparation Schematic. 21
Figure 11. Volumetric Capacitance of the Films in (A) TEABF4 and (B) H2S04...... 21
Figure 12. MCap Structure................................................................................... 22
Figure 13. Preliminary MCap Test Results........................................................... 23
Figure 14. Summary Chart of MCap Results to Date............................................ 23
Figure 15. Specific Energy and Estimated Costs vs. foMc ...................................... 24
Figure 16. Evolution of Ultracapacitors ............................................................... 26
Tables
Table 1: Contrasting Properties of Batteries and Ultracapacitors........................... 4
Table 2: Manufacturers of Ultracapacitors.............................................................. 7
Table 3: Properties of Various Electrolytes Used in Ultracapacitors....................... 8
Table 4: Properties of Various Materials used in Electrochemical Capacitor
Electrode Materials.................................................................................................9
iii
UNCLASSIFIEll/FQA QFFl&IAk W&lii OHL¥
Page 5
UNCLASSIFIED1fFOR 8ffl@IAL tt9! e"t I
Ultracapacitors as Energy and Power Storage Devices for
Commercial and Military Applications
Summary
Ultracapacitors (ultracaps) are energy storage devices capable of extremely
rapid charge and discharge rates with the ability to be cycled hundreds of
thousands of times. These unique capabilities make ultracaps attractive for a
number of applications. The advantages over lithium ion batteries are
somewhat mitigated by the fact that they have less than 10% of the specific
energy (Wh/kg) and require a power converter to regulate their voltage. The
high capacitance is achieved by the enormously high surface area of the
carbon electrodes compared to planar electrolytic capacitors. Ultracapacitors
are commonly used to provide voltage stabilization of power converters and to
supplement peak-power loading of electrical systems. Their application has
expanded from electronics and telecommunications to industrial load leveling
and transportation. Due to their durability, their use in aerospace has been for
munitions fusing and missile power load leveling. Ultimately, application will
be pulsed power storage and delivery for electric propulsion and directed
energy weapons.
Recent developments in ultracapacitors have focused on different active
materials and electrode designs. By using advanced carbons, polymers, and
metal oxides, increased power density and energy density can be achieved.
Oxide-based thin-film ultracaps have demonstrated high-performance energy
and power density, approaching theoretical limits. Carbon nanotubes and
advanced carbons have been used as additives to and solely as electrode
materials. Nanostructured materials and thin-film manufacturing process
improvements will generate breakthroughs in mass production. Magnetic
capacitors are a recent development, manufactured using semiconductor
processes on silicon wafers. They possess a different storage mechanism and
will transform energy storage and pulsed-power applications. Ultracapacitors
are reaching widespread adoption and they are now available to support
electronics through transportation. New advancements in materials will enable
high-energy density devices with exceptional power capabilities.
iv
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Page 6
UNCLASSIFIED1/FOR 8ffl@IAL tt91! e"t I
Chapter 1: Concept
Overview
Ultracapacitors, also known as
supercapacitors, hybrid capacitors,
electrochemical capacitors, electrochemical
double-layer capacitors, or ultracaps, are
energy-storage platforms that offer energy
storage capable of extremely rapid charge
and discharge rates. Ultracapacitors also
have the ability to be cycled hundreds of
thousands of times. The phenomenal
charge and discharge capabilities make
them ideal for supporting volatile memory
and computing applications, energy
efficiency/capture processes, and high
power applications. Ultracaps store their
charge in the electrical double layer
between the electrode and the electrolyte.
Charge storage is a physical mechanism
rather than a chemical phase change, so
these are theoretically capable of cycling an
infinite number of times. 2 One of the
Figure 1. Ultracaps in Various Configurations.'
disadvantages of ultracaps can be a high
self-discharge rate. 3 The charge and discharge voltage output for an ultracap is a
slop ing linear curve, which allows for straightforward and accurate state-of-charge
monitoring. 4 The real advantage of an ultracapacitor is the ability to deliver or accept
bursts of power in a short time.
Ultracaps were introduced in 1966 and found initial use 12 years later as backup power
devices for volatile memory and clocks. Over the last 30 years, numerous advances
have been made that have led to many uses of ultracaps, from transportation to
portable electronics and more. Ultracaps are becom ing more affordable as activated
carbon electrodes and manufacturing improvements have driven costs down. Several
companies now make ultracapacitors to fill a broad spectrum of applications. Figure 1
shows a number of ultracaps with various capacities to fill a range of functions.
Transportation, microelectronics, and aerospace markets are some of the many areas
where ultracaps have become enablers. Advanced materials and improved cell designs
will lead to improvements in both power density and energy density. The improved
performance is expected to make ultracaps important components for efficient power
leveling and high-power receiving and delivery. The unique signature of ultracapacitors
must be understood for aerospace and military applications.
As an electrochemical capacitor, ultracapacitors store energy within the electric double
layer formed at the interface between the electrode and electrolyte. In a conventional
capacitor, the energy is stored by moving charge carriers from one plate to another,
and the charge separation creates a potential. Voltage differentials in a conventional
capacitor are dependent upon the dielectric material separating the plates. In the
ultracap, the electrical double layer is the separation of charge in a vanish ingly thin gap
between two plates. Figure 2 depicts the components and basic design of the ultracap,
1
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Page 7
UNCLASSIFIED11FOR. 8FFl@IAL tt.!! e"t I
showing the electrochemical double layer responsible for the characteristic
performance. 5 The basic principles of operation have not changed with improved
technologies, only the materials and cell design.
The two electrode plates are traditionally the same material, which is usually a
carbonaceous material, such as activated carbon. Each layer is capable of storing a low
voltage, and multiple layers serve to increase the potential. Individual cells are placed
in series to create a higher voltage, in much the same manner as a battery. Recent
advances in ultracapacitors have moved toward employing dissimilar electrodes, which
create a higher potential; since the electrodes are now different, these are sometimes
referred to as "pseudo" or hybrid capacitors . The pseudocapacitor uses a battery-like
electrode to replace one of the carbon electrodes, yielding a high-energy-storage
electrode and a highly capacitive electrode within the same system.
The capacitance of an ultracapacitor can be determined by the Helmholtz equation
(equation 1), which describes the relationship between the electrolyte and the electrode:
C = EA/d
(1)
Here, £ is the dielectric constant of the electrolyte, A is the available surface area, and d
represents the distance between the center of the double layer and the electrode
surface. Increasing the double-layer capacitance in an ultracap is generally
accomplished by either manipulating the electrode (carbon) surface area or the
electrolyte. Energy density (equation 2) is the product of the capacitance and the
square of the voltage:
E = ½ cv 2
(2)
Strategies for increasing the stored energy target improvements to both the electrodes
and the electrolyte. Changing from an aqueous electrolyte to an organic electrolyte with
a higher dielectric constant will increase the voltage from approximately 1 volt to more
than 2.5 volts. Increasing the surface area of the electrode is another approach to
increasing storage capability. There is a tradeoff between porosity and surface area that
must be considered when constructing an electrode with an extremely high surface area.
An activated carbon approaching a measured surface area of 3,000 m 2/g may have less
than half that as accessible or useable area. 6 Increasing the pore size sacrifices surface
area but provides more accessible material. By providing more interfacial area between
the electrode and the electrolyte, a better electrochemical double layer can be produced,
yielding a better ultracapacitor.
2
UNCLASSIFIEO/;LFOA OFFI&il:.l.b YS& OrtLY
Page 8
UNCLASSIFIED1/FOR 8ffl@IAL tt91! e"t I
Activated
carbon
electrodes
Material selection
and construction
0000000000
■ Electrodes
■ Separator
■ Electrolyte
Electrolyte
Separator soaked in electrolyte
0000000000
■ Wound component
■ Case
Activated
carbon
electrodes
Figure 2. Operation of an Ultracapacitor. A si mple ultracapacitor ut ilizes two similar electrod es (typica lly
ca rbon) with a separator and electrolyte to create the electrochemica l double layer that governs operation . 7
BATTERIES AND ULTRACAPS
For an ultracapacitor, energy is stored within the electrica l double layer, which is a
physica l storage mechanism . Contrast this with batteries, where charge and discharge
take place through a chemical (Farada ic) reaction . Since charge is stored physically,
there is no direct degradation mechanism that limits cycle life. Side reactions do occur,
which prevents infinite cycle life, but ultracaps can often be cycled tens of millions of
times .8 Batteries store their energy through chemica l reaction; consequently, cycle life
is much shorter and heavily dependent on the depth of discharge . In contrast, there are
no limitations to the discharge depth with an ultracapacitor. Table 1 addresses some of
the general characteristics of batteries and ultracapacitors, which can help to determine
the preferred system for a specified application . The values are based upon 2008 data,
so some numbers are outdated, but the relative va lues remain consistent. There are
now hybrid devices that blur the boundaries further by introducing a battery-like
electrode to replace one of the two identical electrodes in a traditional ultracapacitor.
3
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Page 9
UNCLASSIFIED11FOR. 8FFl@IAL tt.!! e"t I
Table 1: Contrasting Properties of Batteries and Ultracapacitors9
Characteristic
State of the Art
Charge time
Lithium Ion Battery
~3-5 minutes
Ultra capacitor
"'1 second
~3-5 minutes
~1 second
<5,000 @ 1C rate
>500,000
Specific Energy (Wh/kg)
100-200
5
Specific power (kW/kg)
0.5 -1
5-10
<50% to >90%
<75 to >95%
Cost/Wh
$1-2/Wh
$10-20/Wh
Cost/kW
$75-150/kW
$25-50/kW
Discharge time
Cycle life
Cycle efficiency (%)
The voltage curve for an ultracapacitor is proportional to the depth of discharge,
whereas batteries deliver a relatively constant voltage over a long discharge period. The
sloping voltage curve of an ultracap can be advantageous for state-of-charge
determinations. However, this is also responsible for the decreased energy density
ava ilable in an ultracapacitor. For applications requiring energy to be delivered over a
longer time scale or delivered at a constant voltage, the relatively flat voltage curve
found in most batteries would be the preferred option. In instances where power is to
be delivered or received quickly, or where many cycles are required, an ultracap is ideal.
To better understand the differences between batteries and ultracaps, it helps to think
of batteries as storing watt-hours of energy and ultracaps as storing watts of power. A
Ragone plot illustrates the distinctions by plotting power versus energy in a logarithmic
scale. As can be seen in Figure 3, ultracaps make an excellent option where high power
density is required. The times shown are rough estimates for a full charge or discharge,
which are estimates to help understand the relationship between energy density and
power density. Batteries have made significant improvements to power delivery
recently, but batteries remain the high-energy-density solution . Ultracapacitors are
often thought of as a stop-gap between conventional capacitors and batteries. Recent
developments of hybrid capacitors have led to considerable progress toward higher
energy density. However, there is a tradeoff between high energy density and high
power devices, and the distinctions between the two require consideration of application
requirements when choosing the energy storage platform for a system. The differences
between ultracaps and batteries do not make the two mutually exclusive. There are
applications where either a battery or an ultracap is the preferred energy storage
platform. Quite often, these two can be used together in systems to perform
complementary roles.
4
UNCLASSIFIEO/;LFOA OFFI&il:.l.b YS& OrtLY
Page 10
UNCLASSIFIED1/FOR 8ffl@IAL tt91! e"t I
1000
.......
C')
, .. .s
.c
-
100
C'
10
~
~
Con~entmnal
battene s
"cii
C:
(I)
1
"C
10 hours
>,
...
Cl
(I)
C:
w
0.1
1 second
1 hour
_,II _________
I
I
-- '---------
0.03 second
0.01 .___ _ _ _ _ _ _ _ _ _ _ _ _ ___,
10
100
1000
10000
Power density (W/kg)
Figure 3. Ragone Plot. The graph illustrates the areas where ultracaps and batteries dominate in the power
density versus energy density relationship.
HISTORY
The concept of storing electrical energy in the electric double layer that is formed at the
interface between an electrolyte and a solid has been known since t he late 1800s. In
1966, Standard Oil Company of Ohio (SOHIO) invented the device in the format now
commonly used, which forms the basis for hundreds of patents and t housands of
journal articles. Figure 4 shows a drawi ng from the electrochemical double-layer device
invented by SOHIO. NEC introduced the SuperCapacitor™ in 1978 under license from
SOHIO.
CO
UC. 0'2
Ole.
SA . Alt(S04 3 50
10
lO PEQ.MEABLI:'
Mct.162At-.lcFigure 4. Electrolytic Capacitor as Designed and Patented by SOHIO.
From this point on, ultracaps have rapidly evolved through several generations of
designs. In the 1980s, Matsushita Electric Company developed a method of
manufacturing ultracapacitors with improved electrodes. Initially, they were used as
backup power devices for volati le clock chips and complementary metal-oxide
semiconductor (CMOS) computer memories . As the technology became more
understood, more and more applications were developed for ultracaps. Many other
applications have emerged over the past 30 years, including wireless communication,
power quality, and improved energy efficiency through regenerative energy capture
processes, as found in hybrid electr ic vehicles. 10
5
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Page 11
UNCLASSIFIED11FOR. 8FFl@IAL tt.!! e"t I
Initial ultracaps used aqueous electrolytes made with Ab(SO4)3 (aluminum sulfate),
H2SO4 (sulfuric acid), or KOH (potassium hydroxide) . While these electrolytes have
excellent ionic conductivity, the operating voltage is limited to 1.2 volts using carbon
electrodes. Organic electrolytes have lower ionic conductivity, but the higher dielectric
constant increases the nominal cell voltage up to as high as 3 volts. Carbon has been
used as a high-surface-area electrode material since the inception of the
electrochemical capacitor. It is still the material of choice for many ultracapacitors; one
of the primary reasons is the low cost of carbon materials. However, there are many
types of carbon that are available for use as an electrode material. In addition to
carbonaceous electrodes, metal oxides and conductive polymers are find ing increasing
use in ultracap design. Advancements in the understanding of the electric double-layer
and ultracapacitor behavior have led to better materials utilization and, consequently,
improved devices.
Early electrochemical capacitors were rated at a few volts and had capacitance values
measured from less than one farad up to several farads. Today cells range in size from
small devices with exceptional pulse-power performance in the millifarad range up to
devices rated at several kilofarads. There are even some specialized ultracapacitor cells
now in production that have ratings of more than 100 kF. The technology is
experiencing increasingly broader use, replacing batteries in some cases and in others
complementing their performance. Ultracap technology has grown into an industry with
sales of several hundred million dollars per year that is poised for rapid growth in the
near term due to expansion of power quality needs and the emerging energy
management/conservation applications. 11
Advancements in ultracapacitors have led to numerous devices from an array of
manufacturers. Table 2 compares the various products on the market, showing voltage,
capacity, power density, and additional energy-storage characteristics. Ultracaps have
moved away from aqueous electrolytes and are typically organic electrolytes due to the
increased voltage performance. Electrodes vary from carbon/carbon systems to hybrid
systems using metal oxides or conductive polymers paired with a carbon electrode.
Packaging and sizes of ultracapacitors covers a large range as these are now used from
cellular communications and small electronics to power delivery and management for
seaport cranes. Ultracapacitor technology development is focusing on delivering better
energy density, and this is being approached by improved carbon electrodes, better
electrolytes, and alternative electrodes that provide pseudocapacitive behavior,
including battery-like electrodes. 12
6
UNCLASSIFIEO/;LFOA OFFI&il:.l.b YS& OrtLY
Page 12
UNCLASSIFIED11FOR. 8FFl@IAL tt.!! e"t I
Table 2: Manufacturers of Ultracapacitors 13
Device
V
rated
C
(Fl
Maxwell *
Maxwell
Apowercap **
Aoowercap**
Ness
Ness
Ness (cyl.)
Asahi Glass (pc)
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2 885
605
55
450
1 800
3 640
3 160
1,375
RC
R (mOhml (sec}
.375
.90
4
1.4
.55
.30
.4
2.5
1.08
.55
.22
.58
1.00
1.10
1.26
3.4
Wh/kg
W/kg
(95%)
(1)
(2)
W/kg
Match.
Imped.
4.2
2.35
5.5
5.89
3.6
4.2
4.4
4.9
994
1 139
5,695
2,574
975
928
982
390
8 836
9 597
50,625
24 595
8 674
8 010
8 728
3,471
Wgt.
(kal
Vol.
lit.
.55
.20
.009
.057
.38
.65
.522
.210
(est.)
.34
.60
.63
.50
.21
.414
.211
--.045
.277
.514
.38
.151
Panasonic (oc)
2.5
1 200
1.0
1.2
2.3
514
4 596
.245
EPCOS
2.7
3 400
.45
1.5
4.3
760
6 750
.48
LS Cable
2.8
3 200
.25
.80
3.7
1 400
12 400
.47
BatScao
2.7
2 680
.20
.54
4.2
18 225
.572
2 050
Power Sys. (AC,
2.7
1,350
1.5
2.0
4.9
650
5,785
.151
IPC) **
Power Sys. (GC,
3.3
1,800
3.0
5.4
8.0
486
4,320
.21
.15
pc)**
1 500
1.7
2.5
6.0
776
3.3
.23
.15
6 903
Fuji Heavy
3.8
1,800
1.5
2.6
9.2
1,025
10,375
.232
.143
Industry- hybrid
l(AC/GC) **
JSR Micro
3.8
4
4
.113
.073
1,000
11.2
900
7,987
(AC/GC)* *
3.8
.206
2 000
1.9
12.1
1 038
9 223
.132
(1) Energy density at 400 W/kg constant power, Vrated - 1/2 Vrated
(2) Power based on P=9/16 * (1-EF) * V2/R, EF=efficiency of discharge
* Except where noted, all the devices use acetonitrile as the electrolyte (pc = propylene
carbonate)
AC = Activated Carbon; GC = Graphitic Carbon
** Laminated oouches; all other devices are oackaaed in metal containers
7
UNCLASSIFIEO/;LFOA OFFI&il:.l.b YS& OrtLY
Page 13
UNCLASSIFIED1/FOR 8ffl@IAL tt91! e"t I
Chapter 2: Materials Technology
The standard electrochemica l capacitor is made of two electrodes, an electrolyte, and a
separator, packaged in either a metal container or a laminated pouch. Ultracapacitors
are often packaged in a fash ion similar to a typical battery configuration. The separator
is an ultrathin material that allows ion transport but is electrically insulating. There are
several polymer separators on the market that have the desired porosity needed to
create fast ion transport. The electrodes are traditionally the same material in an
ultracapacitor-this is in stark contrast to a battery. Electrodes are typically carbon; this
is advantageous in making a cost-effective energy/power-storage device . Activated
carbon has a very high surface area, vital to storing energy in the electrica l double
layer between the electrode and the electrolyte. This th in double layer is responsible for
the impressive high-power-storage capabilities of the ultracapacitor. The electrolyte's
resistivity and dielectric constant play a vital role in behavior of the double layer;
consequently, the choice of electrolyte impacts performance.
The earliest electrochemical capacitors were introduced 30+ years ago; they were
symmetric designs (two identical electrodes) in aqueous electrolyte. Wh ile these
electrolytes have excellent ionic conductivity, the operating cell voltage was limited to
~1.2 V/cell and these had a nominal cell rating of ~0 .9 volts . In the second generation
of electrochemical capacitors, the use of organic electrolyte led to an increase of the
rated cell voltage from about 0.9 V/cell to 2.3-2.7 V/cell. Today, ultracapacitors using
an organic electrolyte are the most popular. 14
ELECTROLYTES
Initial ultracaps used aqueous electrolytes, saturated with Al2(SO4)3, or 30%
concentrations of H2SO4 or KOH. While these electrolytes have excellent ionic
conductivity, the operating voltage is limited to 1.2 volts using carbon electrodes.
Improvements to ultracapacitor performance were made by transitioning from aqueous
electrolytes to an organic medium. Organic electrolytes have lower ionic conductivity,
but the higher breakdown potential increases the nominal cell voltage. An increase in
cell voltage up to as high as 3 volts has been realized by use of an organ ic electrolyte.
These electrolytes are typically an ammonium salt dissolved in an organic solvent, such
as propylene carbonate or aceton itrile. Table 3 highlights the comparison between the
various electrolytes used in ultracapacitors. Ionic liquids are beginn ing to become more
common in ultracapacitors , as they allow for an increase in cell voltage to as high as 4
vol t s. These ionic li quids have a higher resist ivity, especi ally at lower t emperatures . The
tradeoff in resistivit y for voltage may be beneficial for some high -power applicati ons.
Table 3: Properties of Various Electrolytes Used in Ultracapacitors 1 5
Electrolyte
KOH
Sulfuric acid
Propyl en e carbonate
Acetonitrile
I onic liquid
Density
Resistivity
(am/cm3)
1.29
1.2
1.2
0.78
(Ohm-cm)
1.9
1.35
52
18
125 (25°C)
28 ( 100°C)
1. 3- 1.5
8
UNCLASSIFIEO/fFOA OFFI&I:.l.b YS& ONLY
Cell
Voltaae
1.0
1.0
2.5- 3.0
2.5-3 .0
4. 0
3 .2 5
Page 14
UNCLASSIFIED1fFOR 8ffl@IAL tt9! e"t I
ELECTRODES
Carbon has been the optimal electrode material for ultracapacitors since their
commercial introduction over 30 years ago. Pseudocapacitor systems use a combination
of a carbon electrode and a battery-like electrode, such as a conductive polymer or a
metal oxide. The hig h surface area of carbon makes it an extremely attractive option
for ultracap electrodes. Carbon chemistry is quite we ll known, and hig h surface area
and low cost ensures carbo n's cont inued use for the near future. While carbon has been
used in electrochemica l systems for many years, there are many nua nces that make its
properties and performance vary significantly amongst the many types of carbon. The
use of a carbon electrode makes ultracaps affordable for use in many systems.
Activated carbon is readily available, can be made from many source materia ls, and is
inexpensive . Materials science activities for electrodes are focused on improving the
carbon electrodes and introduci ng alternat ive materia ls to create an asymmetric
electrode.
Types of carbon can include activated carbon, carbon cloth, aerogels, porous carbon,
carbon nanotubes, and graphene. The properties of carbon can change dramatically
based upon processing, having a major im pact to the porosity and active surface area.
Activated carbon has an extremely high surface area, is inexpensive, and is produced at
a global scale for use in a number of applications. For these reasons, activated carbon
is the traditional carbon of choice for ultracapacitor applications. Recent advances in
carbon materials development have led to a number of options for ultracapacitor
electrodes. Table 4 demonstrates a number of electrode materials in use today and t he
corresponding performance of these ultracaps.
Table 4: Properties of Various Materials Used in Electrochemical Capacitor
Electrode Materials 16
Density
(g/cm 3 )
Material
Activated Carbon
0.7
Carbon Cloth
0.35
Aerogel Carbon
0.6
Porous Carbon from SiC
0.7
Porous Carbon from TiC
0.5
Anhydrous RuO2
Hvdrous RuO2
Doped Conductive Polvmer
2.7
2.0
0.7
Electrolyte
KOH
Oroanic
KOH
Organic
KOH
Orqanic
KOH
Oroanic
KOH
Organic
Sulfuric Acid
Sulfuric Acid
Orqanic
F/g
F/cm 3
160
100
200
100
75
125
175
100
220
120
150
650
450
112
70
70
Previous: DOW-UAP-D146 — AAWSAP DIRD, Aneutronic Fusion Propulsion II, November 2010 · Next: DOW-UAP-D148 — AAWSAP DIRD, Detection and High-Resolution Tracking of Vehicles at Hypersonic Velocities, November 2010
Same topic: title & summary match
Same location: Las Vegas, Nevada
- DOW-UAP-D174 — Utah Ranch Investigation Report, April 2010
- DOW-UAP-D166 — MUFON Reports Prepared for BAASS, November 2008
- DOW-UAP-D168 — BAASS Project Management Plan, December 2008
- DOW-UAP-D169 — BAASS Monthly Report, March 2009
- DOW-UAP-D170 — BAASS Monthly Report, April 2009
- DOW-UAP-D171 — BAASS Monthly Report, June 2009
Same period: 2010
- DOW-UAP-D114 — AAWSAP Contract Modification P00003, May 2010
- DOW-UAP-D113 — AAWSAP Contract Modification P00002, February 2010
- DOW-UAP-D115 — AAWSAP Contract Modification P00004, May 2010
- DOW-UAP-D116 — AAWSAP Contract Modification P00005, September 2010
- DOW-UAP-D131 — AAWSAP DIRD, The Role of Superconductors in Gravity Research, March 2010
- DOW-UAP-D133 — AAWSAP DIRD, The Space Communication Implications of Quantum Entanglement and Nonlocality, March 2010
Same release: Release 06
- DOW-UAP-PR159 — Historical Film of Reported UFOs, Utah, 1952
- LLE-UAP-PR001 — Unresolved UAP Report, Colorado, 2023
- LLE-UAP-PR002 — Unresolved UAP Report, Colorado, October 2023
- DOW-UAP-PR133 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR135 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR140 — Unresolved UAP Report, Middle East, 2022
Same agency: DoW
- DOW-UAP-D094 — Analysis of Flying Object Incidents in the United States, 1949
- DOW-UAP-D097 — Project Sign Progress Report, 1948
- DOW-UAP-D084 — US Army-Flying-Saucer-Study 1949
- DOW-UAP-D155 — Air Intelligence Information Report, Saudi Arabia, 1957
- DOW-UAP-D176 — Triangular UAP AARO Memorandum for Record, 2026
- DOW-UAP-D177 — Unresolved UAP Report, Catalina Island, 1955