DOW-UAP-D143 — AAWSAP DIRD, Laser Lightcraft Nanosatellites, November 2010
File DOW-UAP-D143 is a declassified pdf from Department of War, recording an incident dated 11/1/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.
- File
- DOW-UAP-D143
- Agency
- Department of War
- Incident date
- 11/1/10
- Location
- Las Vegas, Nevada
- Released in
- Release 06 (2026-09-18)
- File type
Topics: AAWSAP & DIRDs
This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.
This DIRD examines laser-propelled “Lightcraft” as a possible low-cost method to launch very small satellites into low Earth orbit by using a remote high-energy laser to supply most of the propulsion energy rather than relying entirely on onboard energy sources. The report combines a survey of nanosatellite trends with a review of “Lightcraft” propulsion concepts, vehicle design, beam-control requirements, and mission studies, and argues that the most promising application is the launch of nano- or pico-satellites, especially Earth- and space-observing payloads of a few kilograms or less. It presents the concept as potentially much cheaper than conventional multistage rockets for very small payloads, while also noting significant practical constraints including strict beam-riding geometry, atmospheric losses, demanding pointing and adaptive-optics requirements, and heavy dependence on large ground-, sea-, or air-based laser infrastructure. Overall, the document presents laser “Lightcraft” as a technically plausible launch concept whose attractiveness depends on whether the supporting laser and beam-control system can be made reliable and economical at operational scale.
Open original file · WAR.GOV page
TL;DR
Even Vegas lights can't out-shine a laser-propelled satellite.
- DIRD D143, DoW, 11/1/10, Las Vegas, NV—technical reference on Lightcraft.
- Analyzes laser-propelled Lightcraft launching nano-/pico-satellites, covering beam control, costs, constraints.
- No official conclusion in the file
AI summary
A Defense Intelligence Reference Document titled "Laser Lightcraft Nanosatellites," prepared by the Defense Warning Office's Technology Warning Division, dated November 2010. The document discusses nanosatellite technologies, laser propulsion, and related studies, including propulsion systems, mission studies, technical specifications, power systems, thermal control, communication designs, materials, testing, instruments, ground systems, autonomy, and propulsion challenges. It details a laser-powered Lightcraft transportation system, mentioning tests at White Sands Missile Range, historical developments, and technical performance. The text covers laser wavelengths, power requirements, vehicle mass, laser power losses, atmospheric effects, cost estimates, and comparisons between Lightcraft and rockets. It also includes concepts for satellite swarms, laser technologies, high-power solid-state and fiber lasers, free-electron lasers, beam control architectures, and collaborations with research institutions. The document focuses on technical details and potential applications of laser propulsion for space access and defense.
Full text
Page 2
UNCLASSIFIED//P'8R 8FFl01iflk W&li QtU.¥
The Defense Intelligence Reference Document provides non-substantive but
authoritative reference information related to intelligence topics or methodologies.
Prepared by:
Technology Warning Division (DW0- 4)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
611thnr·
AAP Person 58
Administrative Notes:
(U) COPYRIGHT WARNING: Further dissemination of the photographs in this publication is not
authorized.
This product is one in a series of advanced technology reports produced in FY 2010 under the Defense
Intelligence Agency, Defense Warning Office's Advanced Aerospace Weapon System Applications. - - -....
(AAWSA) Program. Comments or questions pertaining to this document should be addressed to I -·--. ) MP Person
______
AAWSA Program Manager, Defense Intelligence Agency, ATTN: JUIAF - DI/DWO-3, 1 ·-··AAP Perso~
1
---· Bldg 6000, Washington, DC 20340-5100.
I
ii
UNCLASSIFIED//liQQ OFFIQIA.. W&E &•U:Y
Page 3
UNCLASSIFIED/ /f8R 8FFIGI/Jk W&li QIIL¥
Contents
Chapter 1: Nanosatellite Technologies .................................................................. 3
Chapter 2: Laser Lightcraft Nanosatellite Propulsion .............................................. 11
Chapter 3: Laser Lightcraft Weapon Mission Selection Study .................................. 27
Chapter 4: Summary of Multi-Megawatt Laser Study for Lightcraft Propulsion
Appl ications .....................................................................................................42
Chapter 5: Conclusion ......................................................................................68
References .......................................................................................................71
Figures
Figure 1. Air Force X-25LR Laser Lightcraft .......................................................... 12
Figure 2. AFRL Test Veh icle in Vertical Flight ................................ ........................ 14
Figure 3. Time-Lapse Photo of a Lightcraft Undergoing an Outdoor Vertical Flight Test 15
Figure 4. Lightcraft Flight-Test Vehicle Used in Horizontal Guide -Wire Flight Tests ...... 16
Figure 5. Lightcraft Undergoing Horizontal Guide-Wire Flight Test ........................... 16
Figure 6. Lightcraft Undergoing Horizontal Guide-Wire Flight Test ........................... 17
Figure 7. Lightcraft Concept .......... ...... ................ ... .......... ........... .......... ............ .18
Figure 8. Lightcraft Trajectory and Associated Pointing Angles ................................. 19
Figure 9 . Lightcraft Vehicle Evolution ... ................. ..... ........ ............. .......... ........... 20
Figure 10. Attenuation Effects on Captured Laser Beam Power................................ 22
Figure 11. Influence of Trajectory and Laser Wavelength on Captured Power ............. 22
Figure 12. Captured Laser Power vs. Increasing Range from 11.2 µm CO2 Laser ........ 23
Figure 13. Influence of Lightcraft Range and Po inting Angles on Captured Power........ 24
Figure 14. Ground/Sea-to-Space Concept .............................................................27
Figure 15. Air-to -Space Concept . ........................................ .......... ............ ......... .28
Figure 16. Schematic of Power Oscillator Optics ....................................................44
Figure 17. Schematic of MOPA ............................................................................45
Figure 18. Schematic of the Laser N2/CO2/H2 Gas Flow System ................................45
Figure 19. Northrop Grumman's Joint High Power Bulk Slab Solid-State Laser .......... .48
Figure 20. DARPA's High Energy Liquid Laser Area Defense System ......................... 50
Figure 21. Phase Change Materials Allow Storage of Large Intermittent Heat Loads
While Slow Regeneration Removes Heat from Aircraft ............................................52
Figure 22. Typ ical HPFL MOPA Design ... ...................................... ......................... 54
Figure 23. Fiber Laser Beam Combining Techniques ...............................................54
Figure 24. Pumping Fiber Lasers .........................................................................56
Figure 25. Large and Small Diameter Fiber Lasers .................................................56
Figure 26. Single Mode Fiber Laser Modules ..........................................................57
Figure 27. Multimode HPFLs ................................ ...............................................57
Figure 28. Free-Electron Laser............................................................................58
Figure 29. Free-Electron Laser Mechanism ............................................................58
Figure 30. Free-Electron Laser Electron Beam Phase-Space Evolution ....................... 59
Figure 31. Recirculating-Beam FEL System ...........................................................60
Figure 32. High-Power FEL Optical Resonator ........................................................62
Figure 33. Notional Long Range HEL Beam Control System ..................................... 64
iii
UNCLASSIFIED,tfFQA QFFIGIAI:: 1!181: 8HLY
Page 4
UNCLASSIFIED/ /fOR. 8FFl&IAk W&li ,HIL:¥
Figure 34. HEL Beam Pointer/Tracker............................................ ....................... 65
Figure 35. Basic Shared Aperture Beam Control System ......................................... 66
Figure 36 . HEL Adaptive Optics System ................. ...... ......................................... 67
Tables
Table 1. Laser Lightcraft Model Cost Summary ......................................................25
Table 2. Performance and Estimated Weights for a Hybrid Rocket and Lightcraft ........ 30
Table 3. Estimated Costs for Hybrid Rocket and Lightcraft Launch Vehicles for ETO
Flight..............................................................................................................32
Table 4. Influence of Target Velocity and Intercept Angle on Impact Energy and
Required Mass ..................... ...................... .. .................. ................................... 33
Table 5. Influence of Lightcraft and Target Velocity on Impact Energy and Required
Mass ............................................................................................. .................. 35
iv
UNCLASSIFIED'
Fl'FAR OFFJCJ0L: Pl&li ,>all.¥
Page 5
UNCLASSIFIED/ /fOR. 8FFl&IAk W&li ,>all.¥
Laser Lightcraft Nanosatellites
Summary
Miniaturized satellites are spacecraft of unusually low mass and small size, usually
under 500 kg in total mass. The term "minisatellite" refers to a spacecraft with a wet
mass (including onboard propellant) of 100 kg to 500 kg. Microsatellite or "microsat" is
a spacecraft with a wet mass of 10 kg to 100 kg. Nanosatellite or "nanosat" is a
spacecraft with a wet mass below 10 kg. Picosatel lite or "picosat" is a spacecraft with a
wet mass of 0.1 kg to 1.0 kg. Picosats are also called sub-nanosats.
The primary reason for miniaturizing satellites is to reduce cost. Heavier satellites
require larger launch vehicles of greater cost while smaller, lighter satellites require
smaller and cheaper launch vehicles and can sometimes be launched in multiples or
"piggyback" using excess capacity on larger launch vehicles. Miniaturized satellites
allow for cheaper designs as well as ease of mass production. However, few satellites
of any size other than communications constellations, where dozens of satellites are
used to cover the globe, have been mass produced in practice.
Besides the cost issue, the main rationale for the use of miniaturized satellites is the
opportunity to enable missions that a larger satellite cannot accomplish, such as:
•
•
•
Constellations for low data rate communications.
Using formations to gather data from multiple points.
In-orbit inspection of larger satellites.
Many of these missions require numerous small spacecraft in a constellation or
"swarm." These include orbital communications networks and swarms of small
satellites to conduct remote sensing, and to provide unique perspectives on
astronomical bodies of interest. For instance, 100 or more nanosats could be deployed
from a mother ship to their final destination in space for deployment.
Provisions for orbital maneuvers as well as attitude control, multiple sensors, and
instruments, and full autonomy will yield a highly capable miniaturized satellite. All
onboard electronics will survive a total radiation dose rate of several hundred kilorads
over a several year mission lifetime (at least 100 kilorads over two years) . Nanosats
developed for in-situ measurements will be spin-stabilized, and carry a complement of
particles and fields instruments. Nanosats developed for remote sensing measurements
(MASINT) or surveillance and eavesdropping (SIGINT) will be three-axis stabilized, and
carry a complement of imaging and radio wave instruments. Autonomy both onboard
the nanosats and at the ground stations will minimize the mission operational costs for
tracking and managing a constellation.
To reduce overall mission cost, advanced technology components and a novel laser
propulsion system will be used to make nanosats and their onboard instruments
compact, lightweight, low power, low cost, and able to survive their radiation
environment over a several year lifetime. Each nanosat will be manufactured and
tested for a recurring cost not to exceed $500k. By producing a large quantity of
nanosats for a given mission, the per-unit cost will be reduced to a small fraction of
1
UNCLASSIFIED//FOR 061ilCl.li.k W&& 8Ptl'l
Page 6
UNCLASSIFIED/ /P'OR. 8FFIEiIAk W&i QPd~¥
satellite procurements for traditional missions. Mission operation costs will be
minim ized by the incorporation of both onboard and ground autonomy and use of
heuristic systems.
2
UNCLASSIFIED,'fFQA QFFIEiIAL 1!181!! OHLY
Page 7
UNCLASSIFIED/ /fOR. 8FFl&IAk W&li ,HIia¥
Chapter 1: Nanosatellite Technologies
OVERVIEW
Nanosats require technologies that radically reduce the mass and power of components
without compromising performance. In addition to miniaturizing components, methods
to integrate similar functions across subsystems are being evaluated. For example, all
subsystem electronics, including instruments, could be integrated within the Command
and Data Handling (C&DH) subsystem. Multifunctional solutions also offer significant
savings over traditiona l approaches. Technology investments are required to develop
or adapt components to accommodate the expected radiation environment. Simple,
effective methods of thermal control are essential to keep the nanosat operational
during extreme temperature variations. Autonomy is a critical technology that impacts
every subsystem. Constellations with tens to thousands of nanosats must be highly
autonomous to be practical. The nanosat ground system must be kept inexpensive,
simple, and made inter-operable with other missions.
PROPULSION
In the baseline mission, nanosat propulsion is needed for two distinct functions: 1) each
nanosat must raise its orbit apogee to the appropriate radius, 2) and it must reorient
the axis of the spinning nanosat from the velocity direction (within the orbit plane) to
its science mission attitude (perpendicular to the ecliptic plane). These maneuvers
present challenging velocity change (1W) and attitude-control (ACS) requirements.
Requirements for the Av Thruster:
•
•
•
•
Total impulse: 3,000 to 7,000 N-sec.
Thrust: 445 N maximum.
Input power (during burn): < 1 watt.
Specific impulse: 280 seconds.
Requirements for the ACS Thruster:
•
•
•
•
Total impulse: $ 2.4 N-sec.
Minimum impulse bit: 0.044 N-sec.
Response time: < 0.005 sec.
Pulse rate: 1 Hz.
It turns out that the tiv and ACS thrusters can have independent systems. We propose
a new innovation whereby the nanosat launch vehicle propulsion system also serves
double duty as the tiv thruster system, and this can be done without having to carry the
propulsion energy source into orbit. This can only be achieved via laser propulsion in
which the laser beam energy that is used to launch a nanosat into orbit is also used to
provide tiv thrust in orbit. This novel innovation dramatically reduces the mass, size,
cost, and complexity of nanosats because they will only need to carry minimal onboard
ACS thrusters and propellant to carry out routine, minor attitude adjustments. The
innovative nanosat laser propulsion concept is presented in Chapter 2.
3
UNCLASSIFIED//FOR O61ilCl.li.k W&& 8Ptl'l
Page 8
UNCLASSIFIED/ /fOR. 8FFl&IAk W&li ,HIia¥
Miniaturized solid propellant gas generators could be used as ACS thrusters. Forty
eight 50 mN-sec pulses are required to reorient the nanosat after it achieves the
required orbital altitude. Although this could be achieved either by a monopropellant or
a cold gas thruster, it could also be achieved using an array of gas generators. Such
miniaturized gas generators have already been successfully built and commercialized by
companies such as MOOG and Lockheed-Martin Space Systems. By incorporating
micro-electromechanical systems (MEMS) techniques, the devices have been produced
relatively inexpensively . Miniaturized electric propulsion ACS thrusters, such as pulsed
plasma and MEMS field-emission electric propulsion (MEMS FEEP) thrusters, have been
developed and are now emerging into widespread commercialization.
GUIDANCE, NAVIGATION AND CONTROL
Guidance Navigation and Control (GN&C) subsystem key technologies and concepts
have been identified to enable successful altitude determination of spin-stabilized and
three-axis-stabilized nanosats for future missions. They include miniaturization of a
sun sensor and horizon crossing indicator. The miniature precision "fan" sun sensor will
pinpoint the sun virtually everywhere in the entire celestial sphere with every satellite
rotation. The sun sensor will be required to weigh less than 0.25 kg, draw less than 0.1
watt, operate on no greater than a 3.3 volt bus, and meet a 0.1 ° resolution
requirement. The miniature horizon crossing indicator has a small bore-sight field of
view that is mounted at an angle off the spin axis. As the spacecraft rotates, a cone of
coverage is formed. The sensor must be capable of detecting Earth over a range of
orbital radii with a pointing accuracy of 0.05°. Total horizon crossing indicator weight
and power will be less than 0.2 kg and 0.1 watt, respective ly.
Of particular interest to Constellation missions is the incorporation of GPS onboard the
nanosats, to eliminate ground-based ephemeris generation. This allows for increased
autonomy and simpler, more accurate time resolution onboard the spacecraft. For GPS
to fit within the constraints of a nanosat, t he receiver electronics need to be
miniaturized into a layer within the C&DH module.
COMMAND AND DATA HANDLING
Developing the C&DH subsystem for a nanosat presents some unique challenges, with
low mass (0.25 kg) and low power (0.5 W) requirements being the biggest drivers.
Advanced microelectronic solutions are being developed to meet these challenges. The
microelectronics developed must be modular and of scalable packaging to both reduce
cost and meet the requ irements of various missions. Th is development will utilize the
most cost effective approach, whether infusing commercially driven semiconductor
devices into spacecraft applications or partnering with industry in the design and
development of high capacity data processing devices. The major technologies will
include: lightweight, low power electronics packaging; radiation hard, low power
processing platforms; high capacity, low power memory systems; and radiation hard,
reconfigurable, field programmable gate arrays (RHrFPGA).
The C&DH requirements are as follows:
•
Power: 0.5 watts.
4
UNCLASSIFIED,<,<FOA QFFI&IAL HSI!! OHLY
Page 9
UNCLASSIFIED/ /fOR. 8FFI61Ak U&F QJsll.¥
•
•
•
•
•
•
•
Weight: 0.25 kg.
Input data rate: 2 kbits/sec.
Output data rate: 100 kbits/sec.
Data storage: 2 Gbits.
Encoding: advanced convolutional.
Processing speed: 12 MIPS.
Radiation tolerance: > 100 krads total dose.
In order to develop a low mass C&DH, a lightweight and low power electronics
packaging method must be used. The packaging method that will be chosen must have
a small volume and small footprint (6 cm x 6 cm x variable height). The packaging
technique must provide data on programmable substrates and data on a compliant
interconnects for space use. A multi-chip module (MCM) has been successfully
produced by Pico Systems Inc.
A combin ed effort to reduce mass, power, size and cost led to the development of the
CMOS Ultra Low Power Radiation Tolerant (CULPRiT) system on a chip, and "C&DH in
your Palm" are technologies that enable the power reduction required for nanosats.
The goals of these technologies are a 20: 1 power reduction over current 5-volt
technology, foundry independence of die production, and radiation tolerance.
Another technology enabling a decrease in volume is the RHrFPGA, which reduces
volume by replacing many logic functions/circuits with one die. The RHrFPGA also
allows concurrent design by decoupling the logic design from the module, shortens the
design schedule, lowers the part count, and eases rework.
The above technologies allow for higher levels of electronic integration, effectively
combining spacecraft subsystem electronics and instrument electronics into the
smallest possible mass, power, and volume.
POWER SYSTEMS
Total spacecraft power is limited by the small satellite size. The Sun's power density is
1.35 kW/m 2 . Assuming 15% conversion efficiency for a 0.3 m x 0.1 m disk shaped
nanosat (cross section of 0.03 m 2), with a 67% area coverage, this results in a total
electric power of only 4.0 watts. Lightweight, efficient solar array panels that minimize
the effective array mounting area are needed. Dual or triple junction GaAs solar cells
that give 18% conversion efficiency at end of life (EOL), and assuming a more
optimistic area factor of 85%, will result in only 6.2 Wat EOL. Small satellites that do
not have extended solar panels simply do not intercept a large solar power density and
must use the available power very efficiently. For a small spinning satellite, it is
expected that three solar cells will be connected in series along the spin axis, and
groups of three will be connected in parallel around the circumference. Each section
will generate 3.3 volts and rotate into and out of sunlight as a unit. Voltage drops at
3.3 volts, bus regulation, circuit protection (e.g., fuse or circuit breaker) and Lithium
ion battery discharge characteristics are being studied.
Highly elliptical orbits in the ecliptic plane where the apogee velocity is very low will
cause a several hour eclipse during part of the year. Spacecraft batteries to cover this
eclipse period presents a significant mass impact. However, only a 10° orbit plane
5
UNCLASSIFIED//FOR 061ilCl.li.k U&& 8Ptl'l
Page 10
UNCLASSIFIED/ /fOR. 8FFI61Ak U&i 0'911.¥
inclination relative to the ecliptic, will reduce the maximum eclipse period to about one
hour. Inclusion of spacecraft batteries is then justified. Passive thermal control will be
used to keep the spacecraft electronics within 10°C of ambient temperature, and hence
will not require electric power for heating. Using such a scenario, a battery
requirement of about 2 amp-hours at 3.3 volts will allow full spacecraft functionality
during an eclipse. Twelve AA size Lithium- ion batteries meet the requirement and only
weigh 480 grams.
Circuits that have high current demands, such as thruster solenoids and fuses, need to
be augmented with components that have a lower power density than batteries, but
also have lower internal resistance. Ultra-capacitors are being explored for this
application.
Miniaturization of the power system electronics (PSE) to meet the weight and size
requirements of the nanosats is a considerable challenge. The ideal approach is to
eliminate the PSE completely, by having a fixed electrical load and batteries provide the
needed bus regulation. This yields a simplified system consisting of solar cells,
batteries, and minimal circuitry. A more immediate approach to miniaturization is to
produce hybrid modules that measure approximately 5.08 cm x 3.17 cm x 1.27 cm
and weigh 100 grams for each PSE component, namely the solar array regulator,
battery regulator, and low voltage power converter. The combination of these three
components into one module will reduce the size and weight another order of
magnitude.
THERMAL
Although an inclination change by 10° renders maximum shadows below two hours, we
evaluate the case of a maximum eight hour shadow for the purpose of generality.
Three thermal configurations are considered: (1) top and bottom of the nanosat are
insulated, the inside of the cylindrical solar array is not insulated, allowing internal heat
transfer between the internal equipment and the array; (2) the entire nanosat is
insulated, top and bottom as well as inside the solar arrays, except for a radiator on
top, sized to radiate the internal electrical dissipation; and (3) the internal equipment is
thermally isolated as well as possible from an "outside shell" with a controllable two
phase heat transport device wh ich can be "shut off" during Earth shadows, serving as
the only thermal coupling between the equipment and a radiator on the outside surface.
The key advantage of configuration (1) is its reliability, or robustness. Since the
temperature of the nanosat is set by a high energy balance (heat in - heat out)
dominated by the absorbed solar energy, the operational temperature of the nanosat is
relatively insensitive to top and bottom multilayer insulation (MLI) properties, or,
largely, to internal heat dissipation. However, the feature that yields the operational
reliability, i.e., the high energy balance, also results in a rapid drop in temperature
when the solar load disappears during the Earth shadow. During the maximum eight
hour eclipse used for this evaluation, it was found that internal temperatures dropped
by about 60°C, which would result in internal temperatures in the range of - 30°C to
- 40°C. At the same time, the solar arrays dropped to a temperature of about 60°C.
Based on past experience, these end-of-eclipse temperatures are reasonable.
6
UNCLASSIFIED,<,<FOA QFFIEiIAL HSI!! OHLY
Page 11
UNCLASSIFIED/ /fOR. 8FFI61Ak U&F QJsll.¥
Because configuration (2) has a much smaller overall energy balance than configuration
(1), it is much more sensitive to MLI properties and to internal power dissipation.
However, eclipse performance improves. During the ~ 8 hour eclipse, internal
temperatures drop by only 20°C, a marked improvement, with end-of-eclipse
temperatures well within the range of most spacecraft components. It should be noted
that the solar arrays, since they are now isolated from the body of the nanosat, drop to
temperatures of about - 110°C. Even these solar array temperatures should not pose a
problem. For example, the solar arrays of many geosynchronous satellites drop
routinely to temperatures of about -150°C during the 72 minute eclipse experienced by
these spacecraft at each equinox season.
The key feature of configuration (3) is that the equipment is coupled to an external
radiator only with a two-phase heat transport device, such as a capillary pumped loop
(CPL) or loop heat pipe (LHP). Operational temperatures are again maintained to
temperatures of about 20°c nominal with a properly sized radiator. However, the
temperature is also totally dependent on the proper operation of the two-phase "loop."
The two-phase heat transport device can be made redundant by the addition of a
second loop if single fault tolerance is desired. Note that redundancy is not a
consideration for the other two configurations . During the ~ 8 hour eclipse, further
improvement is realized, with internal temperatures dropping by as little as 6°C if the
internal payload is well insulated from the exterior of the nanosat. As in configuration
(2), the solar array temperatures drop to about -110°C. For certain equipment or
science instruments, the temperature control afforded by this type of "active" design
may be necessary.
A moderate amount of technology development has been underway since 2000 to
enable a two -phase heat transport system for use in a nanosat. The small size and low
heat transport requirements of the nanosat will necessitate significant downsizing of
today's flight qualified two-phase systems. This reduction will be accomplished by
leveraging recent successful tests of a small cryogenic two-phase CPL.
RF COMMUNICATIONS
The onboard RF subsystem must be small, low mass, and low power. The system
specifications are:
•
•
•
•
•
•
•
•
Mass: 0.5 kg.
Power consumption: 0.5 watt.
Transmission data rate: up to 100 kbits/sec.
Command reception data rate: 1 kbit/sec.
Range: 3 to 5 Earth radii.
Channel type: BPSK.
Effective isotropic radiated power: 0.15 watt (-8.2 dbW).
Carrier frequency: 8,470 MHz.
The tracking system should be coupled with this communication subsystem to maximize
efficiency in mass and power.
7
UNCLASSIFIED//FOR O61ilCl.li.k U&& 8Ptl'l
Page 12
UNCLASSIFIED/ /fOR. 8FFI61Ak U&i 0'911.¥
The communications subsystem is further complicated by constellations requiring spin
stabilized nanosats. A spinning nanosat cannot easily point an antenna toward Earth.
Therefore, a low gain omni antenna is assumed and communications must take place
near perigee, when the range is 3 to 5 Earth radii. A large ground antenna and high
data rate compression must be used to achieve reasonable data rates with minimum
power. This places an additional burden on the ground stations for both sensitive
receivers/bit synchronizers and advanced decoders. These same considerations limit
data rate for satellite-to-satellite communication.
Although the inclusion of an onboard command receiver is high ly desired, it puts an
additional strain on an already challenged nanosat mass and power budget. For this
reason, the concept of a totally autonomous, receiverless nanosat design appears most
attractive. However, "receiver-on-a-ch ip" technology has advanced to the point where
including a receiver onboard looks feasible. The biggest disadvantage of a receiver now
becomes the ground personnel and software needed to support the ability to command
the nanosat. Command actions taken onboard will of course be limited to basic
functions such as "transmit data" because of the lack of redundancy and mechanical
functions. Although scenarios have been defined to allow nanosats to autonomously
determine when to transmit their stored data, utilizing a receiver to control the
telemetry downlink from the ground still has value. The capability of uploading flight
software changes, as well as sending a master reset if necessary, would also exist with
such an onboard command receiver.
MECHANICAL AND STRUCTURES
The nanosat mechanical system will be kept as simple as possible. The ideal nanosat
mechanical design should consist of a one-piece structure on which all other
components are mounted.
Multifunctional structures can provide thermal control, shielding and serve as substrates
for printed circuit boards. For example, diamond facesheet honeycomb panels can
serve as a structure, thermal conductor and radiator, and printed circuit board
substrates. The diamond facesheet provides ten times greater thermal conductivity
than aluminum and can dissipate heat from high power density electronics modules
with a low mass comparable to carbon fiber composites. Another example is the
structural battery system. It consists of a honeycomb panel whose core is filled with
the cells of a nickel-hydrogen battery (or other flight qualified cell technology).
Concurrent engineering and fabrication techniques will be used to create a single
computer model for the design, analysis (structural, thermal, and dynamic), and
fabrication of the nanosat and its components. Dynamic modeling capabilities to
simulate nanosat deployments will provide faster designs and a reduction in the amount
of deployment testing required. This approach will significantly lower development
costs by reducing duplication of effort, chances of errors, the number of drawings and
paperwork required.
Mass production techniques not traditionally used for spaceflight hardware will be used,
such as casting and injection molding. Options being considered for the nanosat
structure material are: cast aluminum; cast aluminum-beryllium alloy; injection molded
8
UNCLASSIFIED,<,<FOA QFFIEiIAL HSI!! OHLY
Page 13
UNCLASSIFIED/ /fOR. 8FFl&IAk W&li ,HIia¥
plastic; fiber reinforced plastic; flat stock composite construction; and carbon
nanotubes (a.k.a. "Buckytubes") or carbon nanotubes composited with other materials.
The material will be selected based on mass, cost, manufacturability, ease of assembly
and integration, and suitability for the space environment.
Streamlin ed testing is needed for up to 100 or 1000 nanosats per mission. Performing
a complete test program on each unit wou ld be prohibitively expensive and time
consuming. We need to reduce the quantity of testing required while assuring product
quality to meet program cost and schedule goals. Lot testing and statistical quality
control methods should be developed to verify quality and structural performance by
testing a small subset of the total number of nanosats.
INSTRUMENTS
Instruments for in-situ and remote measurements must be miniatu rized to fit within the
mass and volume constraints of a nanosat. Power consumption must also be scaled
down accordingly. Instrument sensitivities cannot be compromised in the process.
Instrument electronics need to be combined with nanosat subsystem electronics to
achieve higher degrees of integration yield ing reduced mass and volume. Instrument
software will be designed to evaluate the onboard data and adjust instrument data
Previous: DOW-UAP-D142 — AAWSAP DIRD, Concepts for Extracting Energy from the Quantum Vacuum, April 2010 · Next: DOW-UAP-D144 — AAWSAP DIRD, Cockpits in the Era of Breakthrough Flight, November 2010
Same topic: title & summary match
Same location: Las Vegas, Nevada
- DOW-UAP-D174 — Utah Ranch Investigation Report, April 2010
- DOW-UAP-D166 — MUFON Reports Prepared for BAASS, November 2008
- DOW-UAP-D168 — BAASS Project Management Plan, December 2008
- DOW-UAP-D169 — BAASS Monthly Report, March 2009
- DOW-UAP-D170 — BAASS Monthly Report, April 2009
- DOW-UAP-D171 — BAASS Monthly Report, June 2009
Same period: 2010
- DOW-UAP-D114 — AAWSAP Contract Modification P00003, May 2010
- DOW-UAP-D113 — AAWSAP Contract Modification P00002, February 2010
- DOW-UAP-D115 — AAWSAP Contract Modification P00004, May 2010
- DOW-UAP-D116 — AAWSAP Contract Modification P00005, September 2010
- DOW-UAP-D131 — AAWSAP DIRD, The Role of Superconductors in Gravity Research, March 2010
- DOW-UAP-D133 — AAWSAP DIRD, The Space Communication Implications of Quantum Entanglement and Nonlocality, March 2010
Same release: Release 06
- DOW-UAP-PR159 — Historical Film of Reported UFOs, Utah, 1952
- LLE-UAP-PR001 — Unresolved UAP Report, Colorado, 2023
- LLE-UAP-PR002 — Unresolved UAP Report, Colorado, October 2023
- DOW-UAP-PR133 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR135 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR140 — Unresolved UAP Report, Middle East, 2022
Same agency: DoW
- DOW-UAP-D094 — Analysis of Flying Object Incidents in the United States, 1949
- DOW-UAP-D097 — Project Sign Progress Report, 1948
- DOW-UAP-D084 — US Army-Flying-Saucer-Study 1949
- DOW-UAP-D155 — Air Intelligence Information Report, Saudi Arabia, 1957
- DOW-UAP-D176 — Triangular UAP AARO Memorandum for Record, 2026
- DOW-UAP-D177 — Unresolved UAP Report, Catalina Island, 1955