DOW-UAP-D137 — AAWSAP DIRD, State of the Art and Evolution of High-Energy Lasers, March 2010
File DOW-UAP-D137 is a declassified pdf from Department of War, recording an incident dated 3/31/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.
- File
- DOW-UAP-D137
- Agency
- Department of War
- Incident date
- 3/31/10
- Location
- Las Vegas, Nevada
- Released in
- Release 06 (2026-09-18)
- File type
Topics: AAWSAP & DIRDs
This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.
This DIRD surveys the development of high-energy laser weapons and notes that, although lasers had already become important military tools for ranging, guidance, and other lower-power uses, true weapon-class systems remained limited by power generation, beam control, atmospheric propagation, and logistics. The report reviews major laser types along with the optical, tracking, and thermal-management systems needed to make them militarily useful. It argues that high-energy lasers can offer important advantages over kinetic weapons in speed, precision, and low collateral damage, especially against softer or fast-moving targets, while also emphasizing that practical deployment has long been hindered by hazardous chemical fuels, thermal blooming in the atmosphere, power-supply constraints for mobile systems, and waste-heat removal.
Open original file · WAR.GOV page
TL;DR
March 2010 Vegas brief—laser talk hotter than the desert.
- DIRD D137, DoW, March 2010, Las Vegas, NV—technical reference on high-energy lasers.
- Surveys laser types, power limits, beam control, atmospheric effects, and spacecraft vulnerability.
- No official conclusion in the file
AI summary
A classified document titled "State of the Art and Evolution of High-Energy Lasers," prepared by the Defense Intelligence Agency in March 2010, outlines laser technologies, their development, and potential military applications. It covers components and types of high-energy laser systems, including solid-state, slab, fiber, and free-electron lasers, discussing their power levels, thermal management, and atmospheric effects. The text addresses challenges in beam control and propagation, as well as vulnerabilities of spacecraft to laser radiation. It references historical military laser programs and outlines recommendations for protecting spacecraft components from high-energy laser threats.
Full text
Page 1
UNCLASSIFIED/} FOR OFFICIJCL 1191! 9HLY
Defense
Intelligence
Reference
Document
Acquisition Threat Support
31 March 20 10
ICOD : 1 December 2009
DI A-08- 1003-019
State of the Art and Evolution
of High-Energy Laser Weapons
UNCLASSIFIED//F8R 8FFI@IAL HSE 8Ptllf
Page 2
UNCLASSIFIED//5QA QFFl&i,.l YSE BHL1/
State of the Art and Evolution of High-Energy Laser
Weapons
Prepared by:
Acquisition Support Division (DW0-3)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
Author:
AAP Person 79
Administrative Note
COPYRIGHT WARNING: Further dissemination of the photographs in this publication is not authorized.
This product is one in a series of advanced technology reports produced in FY 2009
under the Defense Intelligence Agency, Defense Warning Office's Advanced Aerospace
Weapon System Applications (AAWSA) Program. Comments or questions pertaining to
this document should be addressed to!AAP Person 1
AAWSA Program
Manager, Defense Intelligence Agency, ATTN: CLAR/DWO-3, Bldg 6000, Washington,
DC 20340-5100 .
l
ii
UNCLASSIFIED//J;QA GFJ;IGlifil W&& 8HlV
Page 3
UNCLASSIFIED/ fFOA OFFI€il.t.k YSE &P•tv
Contents
Summary.................................................................................................................v
Introduction ........................................................................................................... 1
Basic Attributes of Kinetic Energy and HEL Weapons ......................................... 1
Elements of an HEL weapon ............................................................................... 2
Laser Devices ......................................................................................................... 3
Laser Fundamentals ........................................................................................... 3
Chemical Lasers ................................................................................................. 5
Solid-State Lasers .............................................................................................. 6
Rod and Slab Lasers ........................................................................................... 7
Fiber Lasers ....................................................................................................... 8
Ultra-Short Pulse Lasers .................................................................................. 10
Free-Electron Lasers ........................................................................................ 11
Beam Control and Atmospheric Propagation of Laser Devices .............................. 12
Brief History of DoD Laser Weapon Research ....................................................... 16
Laser-Material Interaction ................................................................................... 20
Vulnerability of Spacecraft to Laser Radiation ...................................................... 22
Projection of Future HEL Weapon Capability ........................................................ 23
Recommendations ................................................................................................ 25
Sources of Further Information ............................................................................ 26
Figures
Figure 1. Utility of KE and HEL Weapons ................................................................. 2
Figure 2. Elements of an HEL Weapon System ........................................................ 3
Figure 3. Basic Laser Concept................................................................................. 4
Figure 4. Cylindrical Gain Generator for HF Chemical Space Based Laser ............... 5
Figure 5. Common Solid-State Lasers and Their Wavelengths ................................ 6
Figure 6. Incoherent Combination of Single Mode Lasers at the Target.................. 9
iii
UNCLASSIFIED/ fFOA OFFI€il.t.k YSE 8,.LY
Page 4
UNCLASSIFIED/ fFOA. OFFI€il.t.L YSE er•tv
Figure 7. Incoherent Combination of Single Mode Lasers in a Fiber Combiner ....... 9
Figure 8. Free-Electron Laser Wiggler .................................................................. 11
Figure 9. Elements of the 2 kW FEL at Thomas Jeffereson National Accelerator
Facility .................................................................................................. 12
Figure 10. HEL Weapon Basic Tracking and Pointion Controls .............................. 14
Figure 11. Sealite Beam Director ......................................................................... 14
Figure 12. Typical Atmospheric Absorption and Scattering in the Infrared .......... 16
Figure 13. Army Mobile Tactical Unit .................................................................... 17
Figure 14. Air Force Airborne Laser Laboratory .................................................... 17
Figure 15. Mid-Infared Advanced Chemical Laser ................................................. 18
Figure 16. MDA Airborne Laser in a Boeing 747-400F .......................................... 19
Figure 17. The Advanced Tactical Laser C-130 Aircraft.......... ..... ...... .................... 20
Figure 18. Single Pulse Maximum Permissible Exposure ...................................... 22
Tables
Table 1. Laser Systems Irradiance Calculations ................................................... 25
iv
UNCLASSIFIED/ fFOA QFFI€il.t.L YSE 8,.L\f
Page 5
UNCLASSIFIED/ f FO A OFFI€il.t.k YSE &P•tv
State of the Art and Evolution of High-Energy Laser
Weapons
Summary
The laser was invented in 1960, only 49 years ago, and (along with the light
emitting diode) has evolved into an essential part of our modern every-day life
in ways that cou ld not have been foreseen. On the military side, there have
also been incredible advances in laser and beam control technolog ies but no
deployment of any high-energy weapons. Many concepts have been developed
and pursued, only to be discarded or deferred owing to technical immaturity,
expected production cost, lack of apparent utility, or logistics concerns.
The most significant technical impediment to deployment may have been the
large quantities of expensive and hazardous chemicals that were required by
the only available high-average-power lasers. This is now changing with
recent advances in electrically powered lasers (both solid-state and free
electron lasers). As these devices mature over the next few decades, they will
enable practical military weapons at power levels ranging from kilowatts to
megawatts. This evolution may be somewhat slowed or limited in the United
States if there are policy concerns about the use of new types of weapons or
about weaponization of space. As an example, the Department of Defense
developed a microwave device for crowd control, called Active Denial, which
has been shown to produce temporary pain without any injury. However, DoD
was precluded from deploying it owing to policy (not legal) concerns. Other
countries may not exhibit similar restraint, as evidenced by the open
marketing of laser-blinding weapons despite a 1980 Geneva Convention
prohibiting their development or use.
Space offers the ideal environment for laser beam propagation; there is no
atmosphere to either attenuate or spread the beam. As a result, large
distances could be bridged quickly, with range limited by the size of the
transmitting telescope and the potential damage mechanisms limited primarily
by the laser's output power. Initial spacecraft laser weapons are conceivable
within the next 20 years, with the potential for follow-on growth in laser
power and transmitting telescope size. Transmitting telescope size would be
limited by the spacecraft size and competing demands for weight and volume.
Laser power could grow to the megawatt range as solid-state and free
electron laser technology matures, but the major limitation to a spacecraft's
weapon capability may prove to be its ability to generate and store the energy
required by the laser and to store and dissipate the resultant waste heat.
V
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 6
UNCLASSIFIED/ fFOA OFFl&I.t.k YSE &P•tv
Introduction
The purpose of this report is to provide an overview of the current state-of-the-art and
potential evolution of megawatt (MW) class high-energy laser (HEL) weapons.
Implications for space vehicles in or beyond earth orbit will be addressed.
It is rare today to find an individual who doesn't have some concept of a laser weapon.
From Orson Wells's Martian invaders in War of the Worlds, who used them with chilling
efficiency, to the now-classic Star Wars movies, the capabilities attributed to such
devices have grown with time and with writers' imagination. While most fictional
depictions of laser weapons (and many news stories) are without sound basis, these
devices do offer the potential for a whole new class of weapons and capabilities which
may complement (but not replace) existing kinetic energy (KE) weapons and electronic
warfare.
BASIC ATTRIBUTES OF KINETIC ENERGY AND HEL WEAPONS
KE weapons (bullets, shells, missiles, bombs, and so forth) require a finite period of
time to reach the target but are then able to destroy it instantly. They can deliver
immense quantities of explosive energy and destroy large areas. This makes KE
weapons most effective at engaging hardened, large, or stationary targets. Collateral
damage concerns, such as a desired target next to a hospital, enemy forces near
friendly forces, or a sniper target in a crowd can sign ifi cantly limit the opportunity to
use KE weapons. Randomly moving targets also present a challenge for KE weapons
due to difficulties in predicting the target's location at the future time of arrival or in
tracking the target with sufficient accuracy.
High Energy Laser (HEL) weapons, by contrast, begin delivering the laser beam's
energy to the target at the speed of light. However, they require a finite dwell time to
accumulate enough thermal energy (heat) on the aim point to achieve the desired
effect (similar to a blowtorch). The strength of an HEL weapon is its ability to precisely
deliver a limited quantity of energy to a small spot with little collateral damage to
nearby objects or people. The instantaneous measure of a focused laser beam's
effectiveness is called "irradiance" and is measured in power per unit area over the
laser spot (typically watts/cm 2). The beam's ability to inflict damage, by heating during
a time interval, is called "fluence" and is typically measured in joules/cm 2 . Fluence is
simply irradiance x time and one joule is equal to one watt for one second.
Speed-of-light energy transfer, coupled with precision tracking, allows HEL weapons to
efficiently engage softer targets which are highly maneuverable, only visible for short
periods of time, or at extremely long range. Although the initial cost of a laser weapon
might be hig h, the logistics trail is short and the cost per shot is comparatively
inexpensive since the only major expendables are laser chemicals or electricity.
Figure 1 compares t he relative strengths and weaknesses of KE & HEL weapons for
different classes of potential targets. Just as there is a wide variety of KE weapons
(ranging from bullets to precision guided munitions to nuclear weapons) for different
types of applications, one could envision a range of future HEL weapons at different
power levels, wavelengths, weights, volumes, and costs which would be best suited for
specific applications.
1
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 7
UNCLASSIFIED/ fFOA OFFl&I.t.k YSE &P•tv
HEL and Kinetic Weapons offer complementary capabilities
Target
Types
Soft/Smal l/Fast
Moving/tactical
E/O sensors
(Dazzle or Destroy)
Target tagging
Fire starting
Small UAVs
Manpads
Vehicles
Cell towers & comm nodes
Radar antennas
Power grids
Ceramic RF radornes
MilitaryUAVs
Individual persons
Rockets, artillery & mortars
Missiles &
Satellites
Hardened or
Large Area
ICBMs
IRBMs
TheaterBMs
Cruise missiles
Satellites
Tanks
Armored vehicles
Bridges
Buildings
Groups of people
------------------ ----------------------+--------
Laser Power
Laser
1 kW
Weapon
E
Effectiveness
asy
Increasing Laser Power or Increasing Range for Same Effect
10kW
100kW
111Ni
Medium
Difficult
Impractical
Medium
if stationary
if isolated
Difficult
Easy
If stationary
if isolated
---------------------------------------- -- ---KE
Impractical
Weapon
Effectiveness
----------------- ----- ----- ---- ----- ----- -----
Figure 1. Utility of KE and HEL Weapons
ELEMENTS OF AN HEL WEAPON
The purpose of an HEL weapon system is to place and maintain the focused laser beam
on a target aim point for sufficient time to cause the desired heating effect. To
accomplish this, the weapon beam is generated by the laser device, then shaped and
relayed to the input of a pointing te lescope (Figure 2). Laser beam sensors and
steering mirrors are required to maintain the HEL beam centered as it traverses the
optical train. The pointing telescope, which typical ly sits on azimuth and elevation
gimbals, then expands the beam to the diameter of its primary mirror and focuses it to
the range of the target while an imag ing system (which can use a separate telescope or
share the transmitting telescope) acquires the target, tracks it, and points the
transmitti ng telescope's beam at the desired aim point. If the HEL beam's propaga t ion
path from t he weapon to the target includes the earth's atmosphere, it can have a
significant deleterious effect. Absorption and scattering of the beam, which reduce its
strength at the target, are caused by molecular constituents of the atmosphere and
aerosols such as haze or dust. Additionally, atmospheric turbulence spreads the
focused spot and further reduces its effectiveness. All of these factors must be taken
into account when designing a laser weapon.
2
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 8
UNCLASSIFIED/ fFOA OFFl&I.t.k YSE &P•tv
High Power Laser
Device
High Power Optics Pointer I Tracker I
and Beam Shaping Target Designator
Atmospheric
Propagation
Target
TRACKER
EXHAUST
ENERGY SOURCE
Atmospheric,
absorption,
scattering,
and turbulence
Figure 2, Elements of an HEL Weapon System
Laser Devices
LASER FUNDAMENTALS
The term "Laser" is an acronym for Light Amplification by Stimulated Emission of
Radiation. It is a unique device that employs the quantum states of matter to store
and convert energy into electromagnetic radiation. The resulting radiation is referred to
as "coherent," meaning it is single wavelength or "monochromatic" and highly focusable
due to its well controlled phase. In its simplest form, any laser device can be viewed as
an "energy-conversion" box with one input and two outputs. The input is energy, which
can take a variety of forms (electricity, light, or a chemical reaction) depending on the
specific laser, while the two outputs are a coherent beam and heat (Figure 3). Since
the overall energy-conversion lasing process is considerably less than 100 percent
efficient, significant waste heat is generated which must be removed from the laser.
Inside the laser is a "gain-medium" which stores a fraction of the input energy in its
atoms or molecules and then releases the energy at the laser's selected wavelength.
The laser also contains "resonator" mirrors which repeatedly relay the beam back and
forth through the gain medium to increase its energy level. The laser device functions
as the optical equivalent of an electrical oscillator with the resonator optics providing
the feedback. Different lasers, which use various materials as their gain medium, emit
radiation at wavelengths ranging from the infrared through the visible spectrum and
into the ultraviolet.
3
UNCLASSIFIED/ fFOA OFFI&I.t.k YSE 8,.L\f
Page 9
UNCLASSIFIED/ fFOA OFFl&I.t.k YSE &P•tv
Energy
source
(
Lasing Medium
Laser
beam
Waste
heat
Figure 3. Basic Laser Concept
The principles behind the laser were first described by Basov and Prokhorov at the
Soviet Lebedev Institute of Physics in 1952. The first concept demonstration was
actually at microwave frequencies (24 GHz) in 1953 by Townes, Gordon, and Zeiger at
Columbia University. They called their device a MASER for Microwave Amplification by
Stimulated Emission of Radiation. The first working laser, initially called an "Optical
MASER," produced milliwatts of visible light using a ruby rod as the gain medium. This
was done in 1960 by Theodore Maiman at Hughes Research Laboratories in Ca lifornia.
Since then, many types of lasers have found uses in an extremely wide variety of
applications ranging from everyday life (bar code readers, CD players, flashlights), to
industry (cutters, welders, surveyors, levelers), to the military (range finders, precision
guided munitions, dazzlers). These lasers have proven to be inexpensive when
produced in large quantity, rugged, reliable, and safe.
Since the earliest days of the laser, the Department of Defense (DoD) has
conceptualized and led the development of hig h-average-power lasers for weapon
applications. There have been many open literature reports of similar work in Russia,
China, and other countries. Lasers currently exist in a wide variety of forms with many
solids, liquids, gases or even electrons being used for a gain medium to produce beams
over a wide ra nge of wavelengths and power levels. However, only a small group of
laser types have shown the potential to produce weapon level powers.
4
UNCLASSIFIED/ fFOA QFFI&I.t.k Y&E 8,.L\f
Page 10
UNCLASSIFIED/ fFOA OFFl&I.t.k YSE &P•tv
CHEMICAL LASERS
Chemical lasers use a chemical reaction in gas or liquid to re lease the energy which
produces their lasing. A reaction can be initiated with an electric current, by light from
another source, or by simply mixing hypergolic chemicals. These lasers include familiar
low power, sea led gas types such as helium-neon, argon, or krypton-ion and typically
produce light in the visible or near infrared. Excimer lasers are another low average
power sub-category of gas lasers. These use dimer molecules as the lasing medium,
are generally electrically excited, and lase in the ultraviolet.
To-date, every laser which has been
scaled to MW-class average power falls
in the chem ical category . They use
large quantities of rapidly flowing
chemicals to produce reactions which
,.c:.;_i:::~
: ::~=?:.;:~•.i;:;,..~•...
::'.'i
••/~:"'I,
::.--then release the required energy. The
<"- " " " ' ~. .'"::~ ~ ~ ~
carbon dioxide laser (CO2 at 10.6 ~1m)
was the first to be scaled to high power
around 1970 followed by the deuterium
fluoride laser (DF at 3.8 µm) and its first
cousin the hydrogen-fluoride laser (HF
at 2.8 µm) in the mid-1970s. These
devices lase in the far- to mid-infrared
and depend on exciting vibrational and
rotational states of the lasing molecules.
CO2, DF, and HF lasers resemble rocket
engines because they combust a fuel
with an oxidizer. The DF laser ignites a
mixture of nitrogen-trifluoride (NF3)
with ethylene (C2H4) and then injects
deuterium (an isotope of hydrogen) into
the exhaust stream to produce the
lasing molecule of deuterium-fluoride.
Figure 4. Cylindrical Gain Generator for HF Chemical
This laser was the choice of the Navy
Space Based Laser
and Army in the 1970's and 80's for tactical laser development while the HF laser was
the choice of the Strategic Defense Initiative (SDI) for their Space Based Laser
development in the 1980's (Figure 4 ).
The newest chemical laser to be scaled to high power is the Chemical Oxygen Iodine
Laser (COIL at 1.315 µm) which excites vibronic states (simultaneous change of
vibrational and electronic quantum numbers) in monatomic iodine to achieve the near
infrared wavelength. COIL generates light in a more complex process which does not
involve combustion but still releases considerable heat. Gaseous chlorine (Cl2) is mixed
with a destabilized hydrogen-peroxide (H2O2) mixture to produce an excited oxygen
molecule and water. The oxygen molecule is then combined with iodine (Iz) in a
reaction which separates t he iodine molecule into monatomic iodine and transfers the
oxygen molecule's energy to it. Iodine then becomes the lasing atom. This near
infrared laser was the device of choice for the Missile Defense Agency's Airborne Laser
program.
5
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 11
UNCLASSIFIED/ fFOA. OFFI€il.t.L YSE er•tv
Typically in a chemical laser, 10 to 20 percent of the energy released in the chemical
reaction will result in lasing while the other 80 to 90 percent becomes heat.
Fortunately in a flowing gas laser, the heat can be easily removed from the resonator
region of the gain generator by the exhaust gas. It is this efficient heat removal
mechanism which has allowed chemical lasers to be scaled to such high average
powers. If a MW-class laser were required today or in the next few years, chemical
lasers provide the only available options. Because they use large quantities of
hazardous chemicals and need refueling, this type of laser is not a preferred choice by
the military.
The physics and scaling of chemical lasers such as OF, HF, and COIL are well
understood and, in principal, they could be scaled to power levels significantly beyond
the MW level. However, due to the maturity of these technologies, only marginal
further efficiency improvements are likely. As a result, the quantity of chemicals which
must be stored and consumed for a laser beyond ~ 10 MW would make the concept
highly impractical for space-based applications and extremely cumbersome for ground
based lasers. Additionally, the atmospheric degradation of a laser beam propagating
from ground to space makes these wavelengths impractical at power levels beyond 10
MW.
SOLID-STATE LASERS
The earliest and perhaps the most diverse laser category is the solid-state laser which
uses specific atoms or molecules as a lasing gain medium (called the dopant) uniformly
suspended in transparent crystalline or ceramic glass (called the host). For example,
the familiar Nd:YAG laser uses a few percent of neodymium (Nd) atoms as the dopant
suspended in a crystalline mix of yttrium, aluminum, and garnet (YAG). Figure 5 shows
some of the many combinations of solid-state laser dopants and hosts in use or being
developed today.
Wavelength (microns)
0.4
I
I
0. 5
0.6
: isibl e
I
a
·~
0.7
0
0.8
·~
0.9
I
I
1.0
~ear lnfra~d
•I
!,Sapphire
1.1
1.2
1.3
I
I
I
!11
Rhodamine
Nd:YAG X2
1.5
1.6
1.7
1.8
1.9
2.0
I
~~
Nd: YAG
Yb:YAG
Alex and rite
Ruby
1.4
Er: YAG
Er:Yb :YAG
Hosts can include:
Ruby~ Al2 0 3 ::Cr
Sapphire -- Al20 3
YAG"' Yittrium , Aluminum , Gamate"' Y3Al 5 0 12
LuAG"' Lutetium , Aluminum, Gamate"' Lu 3Al 5 0 12
Yittira"' Y2 0 3
,J
Ho:
Figure 5. Common Solid-State Lasers and Their Wavelengths
A major advantage of solid-state lasers for mobile or portable applications is that they
only require electricity to power them although cooling is also needed. For example, a
5 second run of a 15 percent efficient 100 kW laser would require less than one
kilogram of gasoline or diesel fuel. No hazardous chemicals are needed and an
6
UNCLASSIFIED/ fFOA QFFI€il.t.L YSE 8,.L\f
Page 12
UNCLASSIFIED/ fFOA OFFI€il.t.k YSE &P•tv
extremely deep magazine becomes possible. These attributes combine to make solid
state lasers very attractive for both civilian and military applications.
ROD AND SLAB LASERS
The earliest solid-state laser mediums took the shape of a cylindrical rod and were
optically pumped with flashlamps. Higher power solid-state lasers were later made
using larger rectangular slabs since the amount of laser power which can be extracted
increases with the lasing medium's volume. Additionally, rectangular geometries
allowed more efficient optica l pumping and cooling. Newer solid-state lasers were
pumped with semiconductor diodes which emitted light more efficiently than flashlamps
and at wavelengths which were more useable by the gain medium. Like chem ical
lasers, they are considerably less than 100 percent efficient overall and generate heat.
However, soli d-state lasers accumulate heat in the glass lasing medium where the
resulting thermal stresses can distort the lasing beam enough to render it useless or
even crack the glass. Since the glass-based medium is a poor thermal conductor, it is
difficult to remove heat. Thus, thermal management of the gain medium imposes
fundamental limits to increasing the average power in a single slab laser. Much of the
recent research in slab lasers has focused on developing innovative ways to remove this
heat or to combine beams from many smaller slabs.
In order to combine laser beams in a fashion which retains good overall beam quality,
the wavelength, phase, and polarization of the individual beams must be tightly
controlled. This process is referred to as "coherent combination" or "phasing" and
results in the maximum irradiance (watts/cm 2 ) by minimizing the focused spot area
over which the total laser power is spread. If an application (such as welding or
machining) depends more on total power than on minimizing spot size, then coherent
combination is not needed and the laser beams can be separately focused to the same
spot with no regard to differences in wavelength, phase, or polarization. This technique
is called "incoherent combination."
Major progress has been made in slab laser development during the last few years.
Northrop-Grumman, under a DoD-funded program, recently produced 100 kW with
good beam quality. This laboratory device, called the Joint High-Power Solid-State
Laser (JHPSSL), uses a single Nd :YAG master-oscillator that feeds parallel, well-phased
Nd :YAG power amplifiers. Brute-force power scaling, well beyond 100 kW, seems
relatively straight-forward using approaches available today. Unfortunately, as more
lasers are combined the overall beam quality will deteriorate while the parts-count,
complexity, and fragility increases. This makes either militarization at the 100 kW level
or laboratory scaling to/beyond the MW level unlikely in the near-term with this
approach. However, given the recent rate of progress and the relative immaturity of
the technology, it would be reasonable to expect further major technological
breakthroughs in thermal management and phasing, cheaper/more powerful pump
diodes (the major cost today), and far more rugged engineering. These improvements
could be expected to yield affordable, rugged, militarily useful MW-class slab laser
systems with reasonable beam quality within the next 20 years. Much of the relevant
research is occurring outside of the United States.
7
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 13
UNCLASSIFIED/ fFOA OFFI€il.t.k YSE &P•tv
FIBER LASERS
Fiber lasers are also solid-state lasers but are frequently considered separately due
their many differences in implementation. They are made of the same materials listed
in Figure 4 and lase at the same wavelengths. A fiber laser can be visualized as a rod
laser which has been stretched many meters with a resulting diameter about the size of
a human hair. The fundamental reason is to improve heat dissipation. The ratio of a
fiber's surface area to its volume is much greater than a rod or slab and the distance
which heat must travel to the edge of the lasing medium is reduced by orders of
magnitude . The lasing fiber is surrounded by a concentric, larger diameter undoped
fiber into which pump light is injected (usually at the ends) and then allowed to leak
into the lasing fiber along the entire length. Fiber lasers are manufactured or "pulled"
in much the same way as conventional optical communications fibers. Because the
fibers are so thin, the power which can be generated in any one lasing fiber before the
onset of damage is currently quite limited. New approaches to injecting the pump light
and controlling the laser beam as it is generated or amplified are occurring almost daily.
Fibers have been constructed using multiple cores, photonic crystals and air spaces in
order to increase the power of individual fiber lasers with good beam quality and in
ways to combine the beams.
The smallest diameter fiber lasers, which produce single mode beams with very good
wavelength control and stable polarization, have demonstrated a few hundred watts
and are currently thought to have a damage threshold upper bound of about 10 kW.
Small numbers of these beams have been coherently combined using techniques which
match wavelength, phase and polarization of each fiber laser in the cluster. The
bandwidths of these laser/amplifier chains must be extremely narrow ( << 1 GHz) to
maintain polarization and to then be coherently phased to about 01. ). rms. It remains
to be seen how much total power can be generated with good beam quality and what
are the fundamental limits to coherent combining. Phasing research into mechanical
techniques which use deformable mirrors and passive approaches which use stimulated
Raman scattering are both being aggressively pursued. These combining techniques,
when applied to fiber lasers, are in their infancy and offer the potential for weapons
with fairly long tactical ranges.
Other single mode fiber lasers have been produced which generated as much as 5 kW.
Although their outputs are of good beam quality, they lase over a wavelength band
which is too broad to maintain polarization and cannot be coherently combined.
However, these types of beams can be combined incoherently by individually focusing
them onto the same spot (Figure 6), similar to incoherent combination of slab laser
beams or by physically splicing the output fibers of the individual lasers onto a larger
undoped fiber (Figure 7) which can accommodate the higher total power.
8
UNCLASSIFIED/ fFOA QFFI&I.t.k YSE 8,.L\f
Page 14
UNCLASSIFIED/ f FO A OFFl&I.t.k YSE &P•tv
Pointing Telescope
single mode lasers
Figu re 6. I ncoherent Combination of Single Mode Lasers at the Target
Pointing Telescope
'------r---'
Single mode
lasers
Figure 7. Incoherent Combination of Single Mode Lasers in a Fiber Combiner
Previous: DOW-UAP-D136 — AAWSAP DIRD, Biosensors and BioMEMS: A Survey of the Present Field, March 2010 · Next: DOW-UAP-D138 — AAWSAP DIRD, Warp Drive, Dark Energy, and the Manipulation of Extra Dimensions, April 2010
Same topic: title & summary match
Same location: Las Vegas, Nevada
- DOW-UAP-D174 — Utah Ranch Investigation Report, April 2010
- DOW-UAP-D166 — MUFON Reports Prepared for BAASS, November 2008
- DOW-UAP-D168 — BAASS Project Management Plan, December 2008
- DOW-UAP-D169 — BAASS Monthly Report, March 2009
- DOW-UAP-D170 — BAASS Monthly Report, April 2009
- DOW-UAP-D171 — BAASS Monthly Report, June 2009
Same period: 2010
- DOW-UAP-D114 — AAWSAP Contract Modification P00003, May 2010
- DOW-UAP-D113 — AAWSAP Contract Modification P00002, February 2010
- DOW-UAP-D115 — AAWSAP Contract Modification P00004, May 2010
- DOW-UAP-D116 — AAWSAP Contract Modification P00005, September 2010
- DOW-UAP-D131 — AAWSAP DIRD, The Role of Superconductors in Gravity Research, March 2010
- DOW-UAP-D133 — AAWSAP DIRD, The Space Communication Implications of Quantum Entanglement and Nonlocality, March 2010
Same release: Release 06
- DOW-UAP-PR159 — Historical Film of Reported UFOs, Utah, 1952
- LLE-UAP-PR001 — Unresolved UAP Report, Colorado, 2023
- LLE-UAP-PR002 — Unresolved UAP Report, Colorado, October 2023
- DOW-UAP-PR133 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR135 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR140 — Unresolved UAP Report, Middle East, 2022
Same agency: DoW
- DOW-UAP-D094 — Analysis of Flying Object Incidents in the United States, 1949
- DOW-UAP-D097 — Project Sign Progress Report, 1948
- DOW-UAP-D084 — US Army-Flying-Saucer-Study 1949
- DOW-UAP-D155 — Air Intelligence Information Report, Saudi Arabia, 1957
- DOW-UAP-D176 — Triangular UAP AARO Memorandum for Record, 2026
- DOW-UAP-D177 — Unresolved UAP Report, Catalina Island, 1955