Home › Archive › DoW

DOW-UAP-D146 — AAWSAP DIRD, Aneutronic Fusion Propulsion II, November 2010

File DOW-UAP-D146 is a declassified pdf from Department of War, recording an incident dated 11/1/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.

File
DOW-UAP-D146
Agency
Department of War
Incident date
11/1/10
Location
Las Vegas, Nevada
Released in
Release 06 (2026-09-18)
File type
PDF

Topics: AAWSAP & DIRDs

This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.

This DIRD revisits aneutronic fusion propulsion in a more systems-oriented manner, arguing that fusion concepts using low-neutron fuels such as proton-boron or helium-3 could become attractive for space propulsion because they reduce shielding burdens and may support direct conversion of charged-particle energy into thrust or onboard power. The report reviews the relevant fusion plasma physics and focuses on several candidate confinement approaches, then connects those concepts to possible applications in near-space, orbital, and interplanetary propulsion. It presents the most plausible nearer-term use as very high-power electric or plasma propulsion for satellites and deep-space missions rather than atmospheric flight or interstellar travel, while emphasizing that major obstacles remain in ignition, sustained confinement, system mass, power handling, fuel storage, launch integration, and end-to-end engineering.

Open original file · WAR.GOV page

TL;DR

In 2010 Las Vegas, the thing hotter than the fusion ideas was the strip lights

  • DIRD D146, DoW, Nov 2010, Las Vegas NV, AAWSAP program document
  • Analyzes aneutronic fusion propulsion concepts, fuels, confinement methods, and aerospace applications
  • No UAPs reported

AI summary

A document titled "Aneutronic Fusion Propulsion II," prepared by the Defense Intelligence Agency in November 2010, discusses fusion plasma physics, propulsion concepts, and applications. It covers magnetic, inertial, and electrostatic confinement methods, including tokamaks, stellarators, spheromaks, and field-reversed configurations. The text examines aneutronic fusion using deuterium-helium-3 and proton-boron fuels, along with reactor designs and plasma confinement techniques. It references propulsion systems like Dense Plasma Focus and magnetized target fusion reactors, mentioning thrust levels, specific impulse values, and aerospace applications. The document also discusses VASIMR engines, IEC thrusters, and the Bussard Ram Jet concept, outlining a development roadmap from 2000 to 2060. No UAPs or unidentified objects are reported.

Full text

Page 2

UNCLASSIFIED/ FOR OFFICIJ!tt t:99[ 8HL¥

(U) Aneutronic Fusion Propulsion

The Defense Intelligence Reference Document provides nonsubstantive but
authoritative reference information related to intelli ence to ics or methodolo ies.

Prepared by:
Technology Warning Division (DW0-4)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
Authors:

AAP Person 85, AAP Person 88, AAP Person 89

COPYRIGHT WARNI NG: Further dissemination of the photographs in this publication is not authorized.
This product is one of a series of advanced technology reports produced in FY 2010 under the Defense
Intelligence Agency, Defense Warning Office's Advanced Aerospace Weapons System Applications
CMWSA} program Comments or questions pertaining to this document should be addressed to
}\AwsA Program Manager, Defense Intelligence Agency, ATTN: JUIAF !AAP Person 1
DI/DWO-3, Bldg 6000, Washington D.C. 20340-5 100.

ii

UNCLASSIFIED/FOR OEEICI0l 'Uiii Ql'ik¥

Page 3

UNCLASSIFIED/P9R 9ff1@1111L ~9f 8HLY

Contents
Chapter 1: Concept Overview ................................................................................ 1
Chapter 2: Fusion Plasma Physics ......................................................................... 3
2.1

Magnetic Confinement............................................................................ 5

2.2

Inertial Confinement .............................................................................. 7

2.3

Electrostatic Confinement ...................................................................... 8

2.4

Magneto-Inertial Confinement ............................................................... 9

Chapter 3: Fusion Propulsion .............................................................................. 11
3.1

Fusion Reactors for Propulsion ............................................................. 11

3.2

Air Propulsion ...................................................................................... 13

3.3

Ion Propulsion ..................................................................................... 14

3.4

Plasma Thruster ................................................................................... 14

Chapter 4: Applications ....................................................................................... 17
4.1

Near Space ........................................................................................... 17

4.2

Earth Orbit ........................................................................................... 17

4.3

Interplanetary...................................................................................... 18

4.4

Interstellar........................................................................................... 19

Chapter 5: Recent Developments ........................................................................ 21
5.1

U.S. DOE Programs ............................................................................... 21

5.2

International Programs ........................................................................ 21

5.3

NASA Programs .................................................................................... 23

5.4

Privately Funded Programs .................................................................. 23

Chapter 6: Future Developments ......................................................................... 25
6.1

Near-Term Developments .................................................................... 25

6.2

Mid-Term Developments ...................................................................... 27

6.3

Far-Term Development......................................................................... 28

Chapter 7: Conclusions ........................................................................................ 30

iii

UNCLASSIFIED/FOR OFFICIAL t,!E 8HLY

Page 4

UNCLASSIFIED/F(Hl 8FF1&1~1:: W§E 8HI::¥
Chapter 8: Endnotes ............................................................................................ 31

Figures
Figure 1. Fusion Reaction Cross Sections vs. Temperature ..................................... 4
Figure 2. Magnetic Mirror Confinement .................................................................. 6
Figure 3. a) Tokamak and b) Stellarator Confinement ............................................ 6
Figure 4. Field-Reversed Configuration .................................................................. 7
Figure 5. IEC Fusor and Polywell Confinement Configurations ............................... 8
Figure 6. Magnetized Target Fusion Experiment at LANL. ..................................... 10
Figure 7. Dense Plasma Focus (Lawrenceville Plasma Physics) ............................ 10
Figure 8. Specific Power as a Function of Plasma Temperature of Fusion Rocket. 11
Figure 9. Colliding Beam Fusion Reactor .............................................................. 12
Figure 10. DPF Thruster System With Direct Conversion ...................................... 12
Figure 11. Magnetized Target Fusion Reactor ...................................................... 13
Figure 12. MHD Air-Breathing and Fusion Rocket Aerospace Plane ...................... 13
Figure 13. Design of an IEC Jet Thruster - Experimental Device ........................... 18
Figure 14. Comparison of Fusion, Nuclear-Thermal, and Chemical Propulsion for
Same Payload ....................................................................................................... 19
Figure 15. Thrust-to-Weight Ratio and Exhaust Velocity Regimes for Various LongRange Space Propulsion Options.......................................................................... 19
Figure 16. Bussard Ram let.................................................................................. 20
Figure 17. Progress in Tokamak Magnetic Confinement Fusion ............................ 22
Figure 18. ITER Design Concept With BWR Size and Blanket Segment ................. 23
Figure 19. Experiments To Prove a Plasma Fusion Propulsion Concept ................ 28
Figure 20. Roadmap to Aneutronic Fusion Propulsion Development..................... 29

Tables
Table 1: Principal Fusion Reactions ........................................................................... 3
Table 2: Fusion Peak Interaction Temperatures and Fusion Energy to X-rays.........4
Table 3: Fusion Ignition Temperatures.....................................................................5
Table 4: Advanced Fusion Concept Reactor Companies ..........................................24
Table 5: Emerging Technologies ..............................................................................26

iv

UNCLASSIFIED/FOR OFFICIO .. Wli:ili 8HLY

Page 5

UNCLASSIFIED/P9R err1e1wt t,9[ l'84Li

Aneutronic Fusion Propulsion
Summary
Controlled fusion energy production has been under development for 60 years.
The primary objective has been gaining the ability to create terrestrial power
plants using deuterium and tritium as fuel. Unfortunately, this objective has
been eluded for both technical and economic reasons. However, the threshold
for achieving success in applying fusion to propulsion is considerably relaxed,
especially if fuels are used that do not use tritium. Tritium has to be
continuously bred; these reactions yield fast neutrons, which require shielding
and cause structural materials to be periodically replaced. Such "aneutronic"
fusion fuels, such as hydrogen fusing with Boron-11, have been studied
extensively for space propulsion applications since the 1980s.
This report reviews the basic fusion plasma physics, design concepts that
apply aneutronic fusion for propulsion, and the requirements for transitioning
to space. The predominant concepts studied include magnetic field reversed
configuration, dense plasma focus and inertial electrostatic confinement. All of
these concepts have venture capital funded programs for terrestrial fusion
power. When applied to space or near-space propulsion, they can exceed the
performance of any conventional electric thruster.
The future technology development of aneutronic fusion propulsion will
initially be motivated by the very large GEO satellites that will be developed in
the next 20 years for commercial and military broadband communication.
Further development of very-high-power propulsion systems(> 100 kW) to
Mars and beyond will require major developments in all technology areas for
confinement pulsed power and ion fuel beam accelerators.

V

UNCLASSIFIED/POI\ err1e1111t ~§[ 8F.Llf

Page 6

UNCLASSIFIED/ /FOR OfifilCIAk Wlili &P•kY

Chapter 1: Concept Overview
Controlled thermonuclear fusion has been the aspiration for nuclear scientists and
engineers for the last 60 years. During that time, tens of billions of dollars have been
invested in this endeavor with the expected fruition being pushed even further into the
future. When Lyman Spitzer invented the Stellarator in 1951, it was expected to take
only 5 years of concentrated plasma physics experiments to harness the fusion of
hydrogen ions confined by magnetic fields. However, the numerous new instabilities
that arose under increasing higher magnetic confinement pressures have been a
roadblock to the success of controlled fusion.
In 1983, a rediscovery was made by Robert Bussard of a fusion device invented by
Robert Hirsch in his 1966 Ph.D. thesis. The Fusor, as Hirsch named it with his thesis
advisor and famous inventor Philo Farnsworth, simply used spherically concentric
electrodes in a vacuum chamber. When a deuterium gas was supplied to the chamber
and a few-microsecond pulse at 30 kV was applied to the electrodes, D-D fusion
occurred, releasing He and neutrons. Although it released less energy than was needed
to supply the in itia l electric pulse, it provided the evidence for a method to obtain
supplementary heating to ignition of magnetically confined plasmas.
The Fusor led to continued development of what is now called Inertial Electrostatic
Confinement (IEC) devices. Amongst these was the Dense Plasma Focus (DPF), a
plasma production tube invented in 1961, and several other devices. Magnetic
confinement devices utilized the IEC method with imploding layers of lithium or
applying intense beams from either end of a linear magnetic pinch device. This
resurgence of alternate confinement concepts was immediately applied to fusion space
propulsion since it was recognized that there would be an advantage over nuclear
fission propulsion with its costly safety requirements. For mitigating shielding mass and
tritium fuel launch-safety concerns, non-neutron-generating "aneutronic" fusion fuels
were also adopted.
Aneutronic fusion fuels include those isotopes of light elements that when fused
produce no neutrons or a very few from the fusion of daughter products. Although there
are eight such reactions for light nuclei, the most practical for fusion reactors include
the following:
D + 3 He ➔ 4 He + p
P + 7 Li ➔ 24 He

In Chapter 2, we will review the fusion plasma physics needed to apply these
aneutronic reactions to a confinement device to make a fusion reactor practicable for
propulsion, which is described in Chapter 3. In Chapter 4, the relevance of these
aneutronic fusion propulsion concepts will be reviewed and assessed for aerospace
applications including near-space, orbital, and interplanetary propulsion, as well as the
potential for interstellar use. In Chapter 5, we will summarize the recent national,
international, and privately funded R&D that may expedite development, while in
Chapter 6, we outline an R&D path forward for the aneutronic fusion technologies and
systems needed for the next 50 years. Finally, we provide a summary in Chapter 7 that
that conveys aneutronic fusion propulsion:

1

UNCLASSIFIED/ /POlt orr1e1s1tt 1!181! 8HL1/

Page 7

UNCLASSIFIED/ /FOR OPPICl"L U.!I! Grit t
•
•
•

May have near-term applications to replace current satellite ion thrusters and
extend application to interplanetary flight.
Requires extensive technology development for air and near-space applications.
Will not be practical beyond the solar system unless breakthrough propulsion
physics can ass ist the flight to the next stellar system, where fusion "ion
thrusters" can then be used.

Despite the attention propulsion has gotten from the scientific community, the problem
has been insufficiently addressed by the space science community. Although it is
certainly true that the fusion drive train must be successfu l from a theoretical and
experimental perspective before consideration for adaptation to the space environment,
many critical aspects such as Earth-based launch, space-based assembly, space
materials science, safe flight operations, and mission success need to be introduced
early in the design phase. More importantly, now that these fusion propulsion concepts
are starting to look both feasible and attractive, the transition to space and the inherent
aerospace application development need considerable focus.
Toward this consideration, we now begin with a background on plasma physics that
includes fusion efficiencies and confinement schemes for aneutronic fusion, which leads
us to the application to the propulsion concept discussions that follow.

2

UNCLASSIFIED/ /fOR: 8ffl@IAL l:JSE ONLY

Page 8

UNCLASSIFIED/ /FOA OFFl&IAk YSE 8HLV

Chapter 2: Fusion Plasma Physics
At the most basic level, nuclear fusion occurs by forcing atomic nuclei close enough so
that the attractive strong force (which binds nuclei together) overwhelms the very
powerful electromagnetic repulsion force. Under such circumstances the nuclei fuse
together to form a single nucleus, creating an atom of a different element (along with
byproducts such as radiation and neutrons). Because the strong force dominates over
such short-length scales ( ~10- 15 meter, the diameter of a medium -sized nucleus), the
fusion of heavier nuclei are inherently more unstable, with smaller binding energ ies. For
light nuclei, the binding energies of the individual nuclei are significantly smaller than
that of the fused nucleus; it is the released energy of the fusion process (in the form of
high -energy photons or kinetic energy of nuclear products such as neutrons) that is
sought as an energy source. Table 1 shows Fusion reactions including the relevant
aneutronic fusion reactions.
Table 1: Principal Fusion Reactions
Main

, ,rro/1 d

I

i

11

+T-a:+ n
T +p
{ 3 Hc + n

+

E (M e V)

17 .5

+y

T + T d1 •a,1

ue/

a:+_ n

ed fu i

II fuel

+ ~, C--+

+p

p+

L i-+ a,+
r>+7 i - 0"

r>+ II

-

H

30'

To fuse a sufficient number of nuclei within a span of time for practical use, it is
generally necessary to heat an ensemble of atoms to the very high energies shown in
Table 1. These energies (temperatures) are high enough that electrons are stripped
from their associated nuclei, producing a plasma of free electrons and ions. The fusion
reaction cross sections (cr), the probability of interaction for these reactions in barns =
10-28 m 2 , is shown in Figure 1. For the maximum reaction rate temperature, the ratio of
the total amount of energy (kinetic plus radiation) released in the fusion reaction
relative to the bremsstrahlung radiation released is shown in Table 2.

3

UNCLASSIFIED/ /POR. o,,1e1AL l:ISE 8Hk\S

Page 9

UNCLASSIFIED/ /FOR 8Ffl@IAL tl9I!!! er•t t

10

....
C

·::i

10-1

~
~
e 10-2
C

0

u..

\

'.
,,:,

-~
10-J

\

\
\

~

TT \

I

TT

I

I

1
10-S

~-~----~r,~---~---10

1

JO.

Figure 1. Fusion Reaction Cross Sections vs. Temperature
Table 2: Fusion Peak Interaction Temperatures and Fusion Energy to X-rays

fuel

' T
jDiD--D
l - He

Ti (ke\ Pru ·oi PBre_

so
-oo

__9

00

-.3

0

0. -

rr:ahlun•

14-0

0. 1
0 --,,
.

I

If the ratio is low, it takes more confining energy to sustain the reaction. The largest
fusion output is obtained when the temperature is chosen so that <crv>/T 2 is a
maximum (known as the Lawson Criteria), which for plasma ignition is achieved when
the fusion reactions produce enough power to mainta in the temperature without
external heating. This is shown in Table 3 for the most relevant neutronic and
aneutronic fusion fuels. While the ignition temperature is up to a factor of 10 higher for
the aneutronic fusion reactions, the confinement power required for ignition will be one
to two orders of magnitude greater. Th is will therefore require some unique
confinement concepts to achieve ignition.
4

UNCLASSIFIED// FOR OFFICIAL tl!H! OHL\!

Page 10

UNCLASSIFIED/ /FOA QFFI@IAL Y!H! f>HL I
In order to facilitate efficient fusion, it is also necessary to constrain the motions of the
charged particles (i.e., confine the plasma) in an attempt to maximize the likelihood of
ion collisions. Therefore, the net energy produced by the fusion process is more
realistically the released energy minus the energy consumed for plasma heating and
confinement. The fusion energy gain factor, usually expressed with the symbol Q, is the
ratio of fusion power produced in a nuclear fusion reactor to the power required to
maintain the plasma temperature; for the Lawson Criterion, breakeven Q = 1. However,
to provide sufficient energy to convert that power to a useful level, a minimum Q >5 is
needed, and for a power plant to generate electricity the Q should be >30.
For the fusion reactions shown in Table 3, the (D, 3 He) will produce a few fusion
neutrons which can be minimized by running hot and deuterium-lean; however, the
application may be limited by the availabi lity of 3 He. Other reactions to consider will be
the (p, 6 Li) and (p, 11 B). First, a review the most commonly used plasma confinement
methods is needed.
Table 3: Fusion Ignition Temperatures

]

MAGNETIC CONFINEMENT
Magnetic confinement is an often -u sed method for constraining the motion of the
plasma "fuel," increasing the efficiency of nuclear collisions and the fusion process. The
plasma is composed of charged particles and is, therefore, affected by electric and
magnetic fields. Charged particles spira l along magnetic field lines with electrons
spiraling faster and in smaller radii and in opposite directions than their heavier ion
counterparts . As the magnetic field increases at the ends of a magnetic mirror, the
charged particles will reverse direction along the field lines and thus become trapped. A
chamber can be designed such that an appropriate magnetic field configuration can be
produced that guides and constrains the motion of the plasma (see Figure 2). The
pressures (thermal, kinetic, magnetic) of the plasma "gas" are balanced by the high
pressure of the imposed magnetic field-the plasma is "contained" by the magnetic field.
One obvious advantage of this approach is that the imposed magnetic field prevents (or
at least delays) much of the plasma (at energies of tens of keV or temperatures of
several hundred millions of degrees Kelvin) from coming into contact with the structural
elements of the chamber. The pressures are typically on the order of one bar, and
depending on the design, confinement times can span a few seconds to minutes.
Although magnetic confinement designs are in principle steady-state systems, their
primary difficulty is maintaining the strong damping of the various modes of plasma
instabilities that arise in these systems.
5

UNCLASSIFIED/ /FOR OFFJCJ0L n&li ONLY

Page 11

UNCLASSIFIED/ /FOR. OFFICIAL t:191!!! OHL¥

magnetic mirror

pole regions serve as a
magnetic mirror or bottle
that traps and reflects charged
particles - the particles gain
energy

Figure 2. Illustration of Magnetic Mirror Confinement in Vicinity of Jupiter

A second, related magnetic method is to join the ends of the solenoid together as a
toroid, confining the plasma to a ring. A simple toroidal (i.e., circu lar) field, however,
provides poor confinement because the radial gradient of the magnetic field strength
results in plasma drift. A method to reduce drift and produce a stable plasma
equilibrium is to superpose a poloidal magnetic field with the toroidal field, thus driving
a current through the plasma itself. This provides a path for the plasma moving along
the outer edge of the toro id to migrate to the inner edge and vice versa. This is the
method used in tokamak systems (shown in Figure 3). Another solution has been to
structurally modify the toroid chamber into a figure-eight configuration. This allowed
plasma to spend half of the time on the inner portion of the tube, and half of the time
on the outer portion of the tube. Such systems are called stellarators. This configuration
has eventually evolved back into a (non-axially symmetric) toroidal configuration;
rotating the windings in such a manner produces a stable plasma equilibrium while
eliminating the need for a toroidal magnetic field. The fundamental issue with these
confinement systems is that they require superconducting magnetic coils, pressure
vessels, and neutron-energy-absorbing blankets for a 6-meter major radius by 6-meter
high plasma, an enormous technological undertaking-and that is just for an ignition
demonstration (see Chapter 5) .

Figure 3. a) Tokamak and b) Stellarator Confinement

UNCLASSIFIED/ /FOR OFFI&iIAk YS& &PtkY

6

Page 12

UNCLASSIFIED/ /FOR OFFI&ilAl l::181: 8HL'f
A spheromak is a tokamak in a
spherical chamber that uses only a
sin gle set of coils in conjunction with
plasma currents that self-generate a
confining magnetic field. However,
this design is thought to be less
promising than the previously
described technologies for
generating significant fusion energy.

Plasma

Field Reversed
Configuration

Separatrix

re

An FRC (field-reversed configuration)
Open Magnetic
Axial Fi~oils Closed Pololdal
Field Line
Field Line
is an elongated plasma ellipsoid
Figure 4. Field-Reversed Configuration
conducting an azimuthal current that
reverses the direction of an
externally applied magnetic field. The resultant field provides toroidal plasma confine­
ment without requiring a toroidal vacuum vessel or coil set (shown in Figure 4 ). It has
the potential of achieving much higher stable plasma configurations in much smaller
volumes than a tokamak using supplementary laser or neutral beam heating from its
ends. The FRC is susceptible, however, to a tilting mode instability where the confined
plasma ring can flip over and fly apart as the previously confining forces shift radially
outward rather than inward. This can be overcome by magnetic field design. A
significant augmentation of power density for th is concept is to inject the fuel through
the ends with high energy ion or neutral particle beams. Such a system can allow the
very high plasma energy density, temperatures, and confinement times needed for
aneutronic fusion.

INERTIAL CONFINEMENT
Inertial confinement fusion (ICF) is a process by which nuclear fusion is initiated by
heating and compressing a fuel target. Such targets are usually pellets conta ining a
"fuel" of deuterium and tritium atoms. Typical pellets are about the size of a pinhead,
holding ~10 mg of fuel. The process of compressing and heating the pellet is usually
accomplished by one of two methods: using high-energy lasers or using particle beams
(electrons or ions). The vast majority of ICF devices use lasers.
The lasers heat the pellet's outer layer, which explodes this layer outward and produces
a reaction force against the remainder of the target. The lasers either impact the pellet
simultaneously from multiple symmetrically arranged directions or illuminate the inner
wall of a metal cylinder (a hohlraum) containing the pellet (the hohlraum then produces
thermal x-rays which impact the pellet). This force accelerates the fuel inward, sending
shock waves into the pellet's center. If the shock waves are strong enough, they are
able to compress and heat the fuel at the center to such an extent that fusion can occur.
The released energy then heats the surrounding fue l, wh ich may also undergo fusion.
In comparison with magnetic confinement, ICF results in much higher pressures, but at
the expense of a much shorter confinement time.
The goal of ICF is to get a sufficient percentage of the fuel to undergo fusion such that
more energy is released than is used to produce the reaction. Early attempts, however,
have demonstrated that ICF efficiency was much lower than expected. Recent advances
in materials technology and techniques have shown that considerable improvements in
performance are possible; such a test at the DOE National Ignition Test Facility (NIF)
will use 50 TW of laser energy in 192 beams to compress a pellet to achieve ignition.
7

UNCLASSIFIED/ /fOR: 8ffl@IAl l::ISE OHl?f

Page 13

UNCLASSIFIED// FOR OFFICIAL l:ISI: 8HLY
The perennial challenge for developing such a device into a power reactor is the feat of
manufacturing and compressing 10 such 1-mm DT fuel pellets per second. One
significant problem is maintaining equal pressure on the pellets repeatedly to permit
energy production.

ELECTROSTATIC CONFINEMENT
This simple method of confinement is composed of concentric spheres (or sometimes
cylinders) acting as anode and cathode in a vacuum known as a Farnsworth-Hirsch
Fusor or, more commonly, Inertial Electrostatic Confinement (IEC). As shown in Figure
5, the inner sphere (cathode) is not solid, but rather is composed of a wire grid. Ions
entering the vacuum chamber between the anode and cathode are accelerated through
a large potential difference toward the cathode. Passing through the cathode, the ions
collide in the central region, with a small portion of the plasma population undergoing
fusion. 1• 2, 3 However, using this simple setup, it has been argued that net energy
production is not viable for anything other than deuterium-tritium fusion, in part
because the fusion-collision cross section is several orders of magnitude smaller than
the Coulomb-collision cross section. 4 An additional difficulty is that some of the plasma
interacts directly with the cathode, contaminating the plasma with heavy sputtered ions.
A method for mitigating this problem is to eliminate the cathode grid and instead use
magnetic (and electrostatic) fields to create a virtual cathode composed of electrons.
Such devices include the Polywell 5 and the Penning trap. 6 One such Penning trap design
developed at Los Alamos injects electrons into the central region in such a manner as to
produce a harmonic oscillator potential. Called a Periodically Oscillating Plasma Sphere
(POPS), ions in this chamber then also undergo harmonic oscillations and can become
phase-locked with the use of an externally applied radiofrequency electric field.7 8 This
allows the ions to reach very high densities and temperatures as they collide at the
center of the chamber. This promising design eliminates any power loss due to Coulomb
collisions and substantially increases the efficiency of fusion-power generation.
1

Figure S. IEC Fusor and Polywell Confinement Configurations

8

UNCLASSIFIED//FOR OSSICI0~ Ui&i &NL¥

Page 14

UNCLASSIFIED/ /POR. err1e1At l:191!! er•t t
MAGNETO- INERTIAL CONFINEMENT
This method of confinement is an adaptation of the inertial confinement system (ICF)
described above, but also uses some of the methods developed for magnetic
confinement in an attempt to lower the fusion ignition requirements for implosion
velocity and power density. 9 This concept uses a strong magnetic field within a
conducting shell (a magnetic flux conserver). The inertial fusion target plasma lies
within the conducting shell. As the shell is imploded, the magnetic intensity increases
dramatically, constraining and heating the plasma and facilitating fusion. This concept is
being pursued in the United States by the Office of Fusion Energy Sciences of the
Department of Energy. Currently there are two classes: High-gain magneto-inertial
fusion (MIF) and low-to-intermediate-gain magneto-inertial fusion.

High-Gain MIF
The heating power directed into a hot spot for fusion ignition must be greater than the
rate of heat energy loss, and this implies that a high implosion velocity is needed for
high-yield fusion. However, a higher implosion velocity actually lowers the efficiency of
fusion, since less of the cold fuel is assembled (the higher velocity increases the
breakdown of density barriers or growth rate of the Rayleigh-Taylor instability). As
described above, lasers are typically used for direct implosion of the fuel pellet but, to
date, this is not very efficient and the cost per unit energy is high. With a magnetized
target, however, the implosion velocity need not be so high to initiate fusion ignition,
thus lowering the input energy cost without sacrificing efficiency.

Low-to-Intermediate MIF
For low-yield fusion, electromagnetic pulsed power can be substituted for lasers or
particle beams to compress the target. A lower implosion velocity implies that a larger
shell can be used, leading to longer burn duration and a much lower density target. It is
thought that by using an imposed magnetic field, a solid or liquid shell (liner) and a
gaseous target can be used, rather than the usual cryogen ic solid fuel pellets. Such is
the case for the Magnetized Target Fusion experiment being performed at LANL (shown
in Figure 6).
A sim ilar pulsed compression of a fusion fuel gas can be achieved without a target by
instead using Dense Plasma Focus (DPF) having annular electrodes (shown in Figure 7).
In this case a capacitor bank is discharged into the electrodes driving a nanosecond to
microsecond pulse that will heat the plasma created to ignition temperatures. This by
far is the simplest and least elaborate magnetic confinement concept to achieve
aneutronic fusion ignition.

9

UNCLASSIFIED/ /POR. orr1e1At 1:18E 8HL?f

Page 15

UNCLASSIFIED/ /FOR 8FFI€i1Ak l:ISE 8Hklf

Compressed to
thermonuclear
condiUons

Preheated fuel

Figure 6. Magnetized Target Fusion Experiment at LANL

Figure 7. Dense Plasma Focus (Lawrenceville Plasma Physics)

10

UNCLASSIFIED/ /POlt 8FFl@IAk l:IS& 8Nk¥

Text continues in the original file (36 pages).

Previous: DOW-UAP-D145 — AAWSAP DIRD, Aneutronic Fusion Propulsion I, November 2010 · Next: DOW-UAP-D147 — AAWSAP DIRD, Ultracapacitors as Energy and Power Storage Devices, November 2010

Same topic: title & summary match

Same location: Las Vegas, Nevada

Same period: 2010

Same release: Release 06

Same agency: DoW