Home › Archive › DoW

DOW-UAP-D141 — AAWSAP DIRD, Metamaterials for Aerospace Applications, April 2010

File DOW-UAP-D141 is a declassified pdf from Department of War, recording an incident dated 4/6/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.

File
DOW-UAP-D141
Agency
Department of War
Incident date
4/6/10
Location
Las Vegas, Nevada
Released in
Release 06 (2026-09-18)
File type
PDF

Topics: AAWSAP & DIRDs

This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.

This DIRD surveys metamaterials, engineered structures designed to control electromagnetic waves in ways ordinary materials cannot, and argues that their main aerospace value lies in unusual optical and microwave properties together with significant component miniaturization. The report reviews possible applications including sub-wavelength imaging, compact waveguides and lasers, energy harvesting, tunable absorbers, nonreciprocal devices, and switchable materials, with particular emphasis on infrared and microwave uses for sensing, power management, and payload efficiency. It notes that many of the most ambitious applications depend on the practical output of a still-nascent field, especially in optical metamaterials, where only limited demonstrations had been achieved and fabrication remained a major constraint. The document presents metamaterials as a promising advanced materials field with credible niche applications and broader long-term potential.

Open original file · WAR.GOV page

TL;DR

Looks like even April fools needed metamaterials to hide their tricks.

  • DIRD PDF by DoW, 4/6/10, Las Vegas, NV
  • Surveys metamaterials' optical/microwave properties and aerospace miniaturization potential
  • Metamaterials promising niche aerospace uses, but many applications remain nascent

AI summary

A defense intelligence document titled "Metamaterials for Aerospace Applications," prepared by the Defense Intelligence Agency, outlines the definition and properties of metamaterials, their electromagnetic and optical applications, and includes figures and technical details. It dates from April 2010 and is classified as UNCLASSIFIED/AFOR. The document covers various types of metamaterials, including negative index, indefinite permittivity, and complementary metamaterials, discussing their electromagnetic properties, miniaturization potential, and applications like energy harvesting, waveguides, and imaging. It also addresses sub-diffraction imaging, super-lenses, hyper-lenses, and experiments with mid-infrared frequencies. Additional sections cover sub-wavelength imaging, interference, pulse manipulation, dark and radiative antennas, slow light, energy harvesting, infrared absorption, thermophotovoltaics, nonlinear non-reciprocal chiral metamaterials, and THz properties of electric split ring resonators, with references to studies from 2000 to 2009.

Full text

Page 2

UNCLASSIFIED/ {FOR OEFICIP.L YSE 8Ntt

Metamaterials for Aerospace Applications

Prepared by:
Acquisition Support Division (DW0-3)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
Author:

AAP Person 78

Administrative Note
COPYRIGHT WARNING: Further dissemination of the photographs in this publication is not authorized.

This product is one in a series of advanced technology reports produced in FY 2009
under the Defense Intelligence Agency, Defense Warning Office's Advanced Aerospace
weapon System Applications (AAWSA) Program. Comments or questions pertaining to
this document should be addressed to JAAP Person 1
AAWSA Program
Manager, Defense Intelligence Agency, ATTN: CLAR/DWO-3, Bldg 6000, Washington,
DC 20340-5100.

J

ii

UNCLASSIFIED/ /EOR OEFICI,t.L W8!! e»Ntt

Page 3

UNCLASSIFIED/ (fQR OFFIClt.k YSE 8HLI

Contents
Definition of Metamaterials .................................................................................... 1
Applications to Sub-Diffraction Imaging: Super-Lens and Hyper-Lens .................. 6
Applications to Circuits and Waveguide Miniaturization: Slowing Down and
Manipulating Electromagnetic Pulses (EMP) Using Advanced Metamaterials ....... 16
Metamaterials for Energy Harvesting ................................................................... 20
Nonlinear Non-Reciprocal Chiral Metamaterials: For Developing Novel Optical
Isolators and "One-Way" Microwave Mirrors ....................................................... 27
Tunable Switchable Metamaterials ....................................................................... 30
Summary and Conclusions ................................................................................... 31
References ........................................................................................................... 31

Figures
Figure 1. Example of a Metamaterial Component: The Magnetic Split Ring
Resonator (SRR) Design .......................................................................... 2
Figure 2. Example of Another Metamaterial Component: Electric Ring Resonator
(ERR) ......................................................................................................... 2
Figure 3. Geometry of Original Planar Metamaterial Unit Cells (OE1-OE6) and Their
Complements (CE1-CE6) ......................................................................... 3
Figure 4. Recent Optical Metamaterials for Telecommunication Wavelength and
Mid-Infrared Indefinite Permittivity Material .......................................... 5
Figures. Schematic of The Super-lens With n=-1 Refractive Index Corresponding
to ( Surrounded by Vacuum ..................................................................... 7
Figure 6. Schematic of the SiC-based Super-lens Which is Imaging Sub-wavelength
Holes Buried Under the SiO2 Layer .......................................................... 8
Figure 7. Theoretical Concepts (left panel) and Experimental Implementation
(right panel) of an Optical Hyperlens Capable of Magnifying SubDiffraction Objects to Observable (larger than Size................................. 9
Figure 8. Hyperlens Based on a Converging Array of Metal Wires ........................ 10
Figure 9. Far-Field Super-lens (FSL) Based on an Indefinite Permittivity
Metamaterial Placed Between the Object and the Image-Releasing
Grating .................................................................................................. 12
Figure 10. Tomographic Multi-Beam Multi-Detector Holography of Sub-Wavelength
Objects Using Indefinite Permittivity Medium (IPM) ........................... 12
Figure 11. First Experimental Demonstration of Propagating Sub-Diffraction Waves
in the Indefinite Permittivity Medium (IPM) ....................................... 13
Figure 12. Schematic for 2-Beams/2-Detectors Interferometric Measurement
and Numerical Simulation................................................................... 14
Figure 13. Experimental Setup for 2-Beams/2-Detectors Interferometric
Measurement in the Lab and Preliminary Experimental Results .......... 15

iii

UNCLASSIFIED/ {fQR OFEICl.t.ls: W81!! 8flti

Page 4

UNCLASSIFIED// POR: OPPlelAL liSE 8PtLY
Figure 14. Schematic of Pulse Compression in Magnetized Plasma ...................... 16
Figure 15. Trapped Rainbow: A Waveguide With Negative Index Core Can Stop
Light.................................................................................................... 17
Figure 16. "Plasmonic Molecule" Exhibiting EIT ................................................... 18
Figure 17. True Multi-Layer Metamaterial With a Unit Cell Shown in Figure16:
Radiative Antenna (Single Metal Strip) Coupled to a Dark Antenna
(Two Perpendicular Metal Bars) .......................................................... 19
Figure 18. "Perfect" Narrow-Band Microwave Absorber ....................................... 20
Figure 19. Wide-Angle Plasmonic Absorber Based on Negative Index
Metamaterial ....................................................................................... 21
Figure 20. Specific Design of a Wide-Angle Plasmonic Absorber Based on Negative
Index Metamaterial Operating at A= 1550 nm ..................................... 22
Figure 21. Experimental Reflectivity vs. Wavelength and Theoretical Plot of
Reflectivity Contours ........................................................................... 23
Figure 22. Preliminary Attempts to Design a Better Absorber Using Complementary
MetaMaterials (U-shaped C-MM) ......................................................... 25
Figure 23. Engineering the Complex Reflectivity Coefficient Using the Concept of a
MetaMirror.......................................................................................... 26
Figure 24. Example of a Generic Chiral Metamaterial ........................................... 28
Figure 25. Example of Time-Irreversibility of Light Propagation Inside the Twisted
Fiber Core............................................................................................ 29
Figure 26. THz Properties of an Electric Split Ring Resonator .............................. 31

iv

UNCLASSIFIED/ {EAR OFEICll.k WSI!! eNti

Page 5

UNCLASSIFIED/ (FOR OFFIClt.k YSE 8Htt

Definition of Metamaterials
A metamaterial is defined as an artificial medium whose properties (mechanical, optical,
magnetic, or other) cannot be found in naturally-occurring materials. The emphasis of
this study will be on electromagnetic and optical metamaterials. Such metamaterials
can exhibit rather extreme properties, such as negative refractive index, which implies
that both electric permittivity and magnetic permeability must be negative
( £ < 0 µ < 0) (Reference 1). Such meta materials used to be called " left-handed"
I

because of the unusual phase re lationship between the electric and magnetic fields.
Specifically, in most (positive index, including vacuum) media one uses the right-hand
magnetic field (
and the
rule to define the relationsh[p between electric field (
propagation wavenumber ( f ). The physical basis of the right-hand rule is that the

E)

direction of energy propagation defined by the Poynting vector

H),

S= cEx HI 47Z' and the

direction of the phase velocity (defined by the wavenumber k) must coincide. That
does not hold true for negative index metamaterials where the two directions are
opposite, therefore, t he left-handed relationship must hold for the three vectors.
Nevertheless, the "left-handed" designation did not withstand the test of time because
it was causing confusion and creating irrelevant allusions to helica l (a.k.a. chiral)
structures. Although chiral structures can indeed exhibit negative index behavior
(Reference 2), chirality is not necessary.
A typical metamaterial consists of resonant elements such as Split Ring Resonators
(SRR). An example of an SRR is shown in Figure 1. The main function of the SRR is to
enable strong magnetic response of the structure. A simple empirical formula exists for
the magnetic permeability of a metamaterial comprised of the SRRs:

(1)

where {J)M is the resonant frequency of the SRR, and F is proportional to t he volume
filling factor of SRRs. It is noteworthy that SRRs are designed in such a way that it has
a large capacitance. As the result, the resonant freque ncy of an SRR is small, (that is,
the SRR-containing cell is very sub-wavelength). In the example shown in Figure 1
(taken from Reference 6), the unit cell operated at {J)j27Z" = 10 GHz is A/10. I n fact, the
sub-wavelength size of the meta material is what distinguishes them from their close
cousins: photonic crystals. By properly designing magnetic SRRs, it is possible to
achieve any value of µ for any given frequency. Special challenges exist for optical
structures, though, as will be explained below.

1

UNCLASSIFIED/ {fQR OFEICl.t.ls: W81!! 8flti

Page 6

UNCLASSIFIED/ (EOR OFFICit.k W&E 8Htt

C I.

r

I
2

0.260

1.654

0.003

0.254
0.-45
0. 0
0.20
0.190

1.677
1.7 1
1.771
I. 25
I. 6

.023
.052
.0
.1..0
.1

0.17

1.9 I

0.148
0.129
0.116

2.027
2.110

.I
.220
.2 0
0.279

3
4
6
7
9
10

I.Lr

2.

r1yun: .L , cxc1mp1t: u, i:I r111::cc1 mc1 c11::nc11 1.,umpun 11::nc; 1n - ,.,_,..,_., _ -,-........,. _____ ., ___ , ,---· ·, _ _ _ ,,. ... .. ,~

in-plane lattice pa ram eters are av = a,= 10/3 mm, The ring is square, with edge length I =3 mm and t racewidth w
= 0. 2 mm. The substrate is 381 µm-thick Duroi d 5870 (E = 2.33, td = 0.001 2 at 10 GHz, where td is t he loss
ta ngent) . The Cu fi lm, from wh ich t he SRRs are patterned, is 17 µm th ick. The parameters ra nd s are given in the
ta ble together with t he associated value of µ,. (Reference 6)

Elect ric properties of met amaterials can be similarly contro lled. An example of a planar
elect rically -active metamaterial is shown in Figu re 2.

-

-

Figure 2. Example of Another Metamaterial Component: Electric
Ring Resonator (ERR). This com pone nt provides tu nable resona nt
electric response to the incident electromagnetic fiel d, and can be
util ized for engineering t he freque ncy -dependen t dielectric

permittivity &( w) . Possi ble app lication : THz and microwave absorbers,
( Reference 7)

2

UNCLASSIFIED/ {EAR OFFICIAk W81!!! Bflti

Page 7

UNCLASSIFIED//POR. Offl@IAL YS! OP~LV
The electric response of such (or similar) metamaterial is given by
(2)

where w R is the resonant frequency and r is the loss coefficient.
Negative index metamaterials are by no means the only potentially useful metamedia.
Several new concepts such as Indefinite Permittivity Metamaterials (1PM) (References
3, 4) and Epsilon- Near-Zero (ENZ) metamaterials (Reference 5) have recently emerged
and found some exciting applications t hat will be reviewed below. IPMs ca n be used as
ultra-compact spatia l filters (both high -pass and low -pass) whereas ENR metamater ials
can be used for making sub- wavelength waveguides capable of coupling close to 100
percent of the incident rad iation (Reference 8), as well as directing it around tight
bends with negligible bending losses. Yet another class of planar metamaterials,
complementary metamaterials (CMMs), has recently emerged (Reference 7). Instead of
using metallic structures deposited on a substrate (left panel of Figure 3), CMMs consist
of slits in the continuous metal screen (right panel of Figure 3). The shape of the slits
coincides with that of the materials themselves. Such complementary metamaterials
have been recently used for making epsilon-near zero waveguides (Reference 8).
CE1

CE4

CE2

CE5

CE3

CE6

Figure 3. Geometry of Original Planar Metamaterial Unit Cells (OE1-0E6) and Their Complements
(CE1-CE6}. The polari zation of normally incident electromagnetic rad iation is configured as shown in OEl
and CEl for the original and complementary metamaterials, respectively. (Reference 9)

3

UNCLASSIFIED/ {EAR OFFICI.IJ.k WSI!!! tJflti

Page 8

UNCLASSIFIED/ (EAR OFEICJ0k W&E 8Htt
In general, metamaterials offer a new way of designing electromagnetic structures with
arbitrary values of permittivity/permeability tensors, as well as other parameters (such
as bi-anisotropy coefficient). In many instances, metamaterials enable us to
considerably minimize sizes of resonators, transmission lines, and so forth. Such
miniaturization is possible due to the resonant nature of the individual unit cells.
Specifically, the structures shown in Figure 3 have high capacitance; therefore, their
individual sizes are very sub-wavelength. That enables arrangement within sub­
wavelength units that can be densely packed and result in strongly miniaturized
components. It is this miniaturization that makes metamaterials interesting for
aerospace application where small weight and size are essential.
While the most spectacular progress in the field of electromagnetic metamaterials has
so far occurred in the microwave range, it is the optical (visible, infrared, mid-infrared)
spectral regions that hold most promise for revolutionary applications. Electromagnetic
metamaterials have a tremendous potential for revolutionizing propagation, storage,
and conversion of electromagnetic waves across the entire Electromagnetic Spectrum.
In our opinion, the most exciting applications that are relevant for aerospace
applications include energy harvesting, developing novel optical devices with unusual
yet practically important capabilities (for example, non-reciprocal devices), enhancing
the efficiency of nonlinear optical devices, developing novel imaging modalities capable
of breaking the diffraction limit (for example, super-lenses, hyper-lenses, far field
super-lenses), and developing novel lithographic techniques.
Optical metamaterials are still a very new area. Just a handful of experimental
demonstrations of multi-layer (truly bulk) optical metamaterials exist at the moment.
Among the most recent ones are (a) demonstration of the negative index optical
metamaterial at the telecommunications wavelength (Reference 10) that used the so­
called fishnet structure shaped as a prism for demonstrating Snell's Law, and (b)
demonstration of the Indefinite Permittivity Material (IPM) and negative refraction
(which, in the context of anisotropic metamaterials, is not the same as negative
refractive index) in the mid-infrared part of the spectrum (Reference 11). These
structures have the distinction of being multi-layer (or bulk). Most previous examples of
optical metamaterials have dealt with single or double-layer substances which cannot
be, strictly speaking, characterized as metamaterials. The difficulty in obtaining strong
magnetic activity in optical metamaterials has been explained in several recent reviews
(References 12, 13). In a nutshell, the issue is that the magnetic moment of most
structures (including atomic systems) is very small, much smaller than the electric
moment. Therefore, it is difficult to observe any optical effects that can be clearly
assigned to magnetic activity. This is especially true for the structures that are much
smaller than one wavelength. Exceptions, such as artificially constructed split rings, are
possible. However, such structures cannot be operated at very high frequency because
of the excitation of electrostatic resonances (Reference 12). In other words, when the
resonant frequency is too high (or the dielectric permittivity of a metal is not sufficiently
large), electrostatic resonances disrupt magnetic activity. More specifically, the energy
inside and in the vicinity of a metamaterial element (for example, Split Ring Resonator)
becomes predominantly electrostatic, (that is, in the form of the kinetic energy of
oscillating electrons). The recently described multi-layer fishnet (Reference 10) is not
an exception: its unit cell (that is, the lateral period) is only one-half of the operating
wavelength.

4

UNCLASSIFIED/ {EAR OFEICll.k W8I!! eNti

Page 9

UNCLASSIFIED/ ( FOR OFFIClt.k YSE 8Htt

10

12

14

WmOfllllll{)lml

Figure 4 . Recent Optical Metamaterials fo r Telecommunication Wavelength A = 1.5 1,1m (Left and
Middle) and Mid-Infrare d IPM . The mu lti- layer fishnet is made of si lver films separated by a dielectric spacer. A
focused ion beam was used to produce the prism-shaped fishnet. The 1PM was obtained by depositing interleaved
80 nm layers of Ino.s3Gao.41As and Alo.. slno.s2As. The layers, approximat ely 8.1 µm thick, grow n by molecular beam
epitaxy on lattice-matched InP substrates. The InGaAs layers were uniform ly doped to create different values of
permittivity in alternating layers. (Reference 10 and 11)

That is not to say that there is not ongoing theoretical and experimental work on
designing optical metamaterials for practical applications. The author's research group
at UT- Austin, has designed the first Plasmonic Negative Index Metamaterials (P-NIM)
super-lens (Reference 14 ), developed novel techniques for analyzing optical properties
of plasmonic nanostructures, (including band-structure calculations of periodic
nanostructures) (Reference 15) and quasi-static calculations of plasmonic resonances
(Reference 16). The UT-Austin group has also designed a number of unique sub­
wavelength P-NIMs in the optical part of the spectrum (References 14, 17, 18), and has
recently published a review of optical P-NIMs (Reference 12). The group has also
contributed to developing and experimentally implementing the concept of the "perfect
lens" (Reference 19) based on plasmonic/polaritonic materials. A perfect lens enables
imaging of sub-wavelength objects in the infrared part of the spectrum, including
objects buried under the surface. Also developed is a Wide-Angle "Perfect" Absorber of
Mid-Infrared Radiation {WAPAMIR) (Reference 20) based on the negative index
metamaterial whose impedance is perfectly matched to vacuum.
Below is a concise summary of various topics/applications that are especially suitable
for the aerospace industry. This study concentrates on the facility of meta materials to
miniaturize various optical and microwave components. Metamaterials can also be used
for imaging very small (sub-wavelength) objects without resorting to costly and space­
consuming near-field scanning optical microscopy. Also described are the ongoing
efforts in the field to make extremely compact metamaterials-based lasers. Smaller
lasers mean smaller weight and more room for other diagnostic devices and useful
payload within the confines of a space vehicle. Applications of metamaterials to photon
harvesting is especially fitting for advanced aerospace platforms because of the
necessity to collect electromagnetic energy for battery recharging, diagnostic
spectroscopy, and other vital functions of a space vehicle.

•

Complementary Metamaterials for Energy Harvesting. Development of ultra­
thin photovoltaic and thermo-photovoltaic cells is hampered by weak photon
absorption in semiconductors. Metamaterials can modify absorption making it
wavelength-selective (tunable), highly efficient, and, if desired, wide-angle. Recently
a way has been found for creating quarter-wavelength resonators backed by leaky
mirrors made out of CMMs.

5

UNCLASSIFIED/ {fQR OFEICl.t.ls: W81!! 8flti

Page 10

UNCLASSIFIEr,//POR: OPPIEll<L tt.!I!! 9HL3f
•

Far Field Super-Lens Based on the Interferometry of Sub-Diffraction Waves.
Sub-diffraction imaging has long been considered to be possible only using near­
field microscopes. Those are fairly complex, slow-scanning, and large devices that
are not appropriate for advanced aerospace platforms. Metamaterials enable new
imaging modalities: super-lenses, hyper-lenses, and far-field super-lenses. In
addition to a survey of the existing scientific literature, novel ideas on developing a
new interferometric Far-field Super-Lens (FSL) based on the multi-beam multi­
detector technique utilizing materials with Indefinite Permitivity Tensor are
presented. Fabrication of such Indefinite Permittivity Materials (IPMs) for the mid­
infrared part of the spectrum is achieved and demonstrates the capabilities of
transmitting electromagnetic waves with the spatial period much smaller than the
vacuum wavelength of light. Interference between sub-diffraction waves enables
disentangling multiple diffractive orders and extracting their amplitudes.

•

Nonlinear Non-Reciprocal Chiral Metamaterials: Developing Novel Optical
Isolators and "One-Way" Microwave Mirrors. These developments are
motivated by the need to construct one-way "light diodes" for compact optical
isolators. Presently there are two approaches to optical isolation: the most common
using magnetic fields, and the less developed based on using nonlinearities. A
different approach relies on the phenomenon of adiabatic mode conversion in
nonlinear chiral metamaterials. Preliminary theoretical results for a simple chiral
fiber with a variable twist period (pitch) that enables full transmission of a tightly
confined core mode in the forward direction and full mode-conversion of the core
mode into a cladding mode for the backwards propagation is obtained.

•

Slowing Down Light and Miniaturizing Optical Components Using the
Phenomenon of Electromagnetically Induced Transparency in
Metamaterials. The speed of light places a natural limit on the size of
optical/microwave components. Metamaterials offer an exciting opportunity to slow
down light. This has two major implications: (a) light can be stored/manipulated in
smaller volumes, and (b) nonlinear effects are strongly enhanced by the resulting
energy compression.

Applications to Sub-Diffraction Imaging: Super-Lens and
Hyper-Lens
The super-lens is one of the earliest applications of metamaterials (Reference 21), and
its principle is shown is Figure 5. Without the super-lens, all information about sub­
diffraction (or sub-wavelengths, which is equivalent) features of the periodic object
would have been lost. The reason for the information loss is evanescent decay of the
large spatial wavenumbers. The only method of accessing/measuring these features
would be to scan the object using a near field scanning optical microscope. By inserting
a super-lens between the object and the imaging plane, evanescent waves may be
amplified and the image transferred forward. Unfortunately, this approach by itself does
not remove the need for a near-field scanning device; the image that is recreated in the
imaging plane is still sub-wavelength, and needs to be read out.

6

UNCLASSIFIED/ {EAR OFEICl.t.ls: Y81!! 9flti

Page 11

UNCLASSIFIED/ (fQR OFFIClt.k YSE 8HLI

A>d

.
=

Figures. Schematic of the Super-Lens with n=-1 Refractive Index Corresponding to(£= -1, µ
-1)
Surrounded By Vacuum. Super-lens' presence enables imaging sub-diffraction objects such as the period ic
grating shown here.

There are, however, interesting circumstances when it is very important to transport
the image towards the scanning device. One such special circumstance is spatially­
resolved spectroscopy of small (for example, cellular) structures. One can envision
space expeditions to other planets that could, potentially, result in finding some
evidence of primitive cellular-level life. It would then be highly desirable to examine the
structure of the living cell in its natural environment. In all likelihood, that environment
would be liquid. Therefore, it would be very desirable to examine the cell without
actually touching it with a tip of a near-field optical microscope. Thus, the sub-surface
imaging of a small object which is buried underneath a liquid layer would be necessary.
No such experiments have so far been conducted. However, several years ago t here
was an experiment demonstrating imaging of sub-diffraction objects buried under the
layer of silicon dioxide.
The schematic and experimental results from the experiment (Reference 19) are shown
in Figure 6. In this experiment the sub-wavelength objects were simple holes that were
mill ed in the metal using an FIB. They were buried underneath the super-lens
consisting of SiC (negative epsilon material for mid-infrared frequencies) and silicon
dioxide (positive epsilon material). Note that this configuration (materials with 6 1 > 0
and 6 2 ~ - 6 1 < 0 joined together: sandwiched or positioned next to each other) is typical
for a near-field super-lens. The difference between the near-field super-lens shown in
Figure 6 and the " ideal" super-lens shown in Figure 5 is that the ideal also requires a
material with a negative value of magnetic permeability.

7

UNCLASSIFIED/ {fQR OFEICl.t.ls: W81!! 8flti

Page 12

UNCLASSIFIED/ (fQR OFFIClt.k YSE 8HLI

a

Figure 6. Schematic of the SiC-Based Super-Lens Which is Imaging Sub-Wavelength Holes Buried Under
the Si02 Layer. The imaged objects are >../20 holes milled in gold using FIB . The scattered signal is picked up by
the tip of an NSOM and directed towards the I R detector. Depending on the imag ing wavelength, either amplitude
(e) or the phase (f,g) of the signal are prominent.

As the laser beam scatters off the sub-wavelength holes, its electric field is picked up
by the tip of a Near-Field Scattering Optical Microscope (NSOM) and re-scattered into
the far-field. There it is interfered with the reference pulse and picked up by an infrared
detector. Note that this interferometric technique enables one to extract both the phase
and amplitude of the field, as shown in Figure 6. This significantly broadens the spectral
range over which the super-lens yields meaningful information . For example, the
amplitude contrast is highest at A = 10.85 µm shown in panel ( e) while the phase
contrasts are the highest at A =11.03 µm and A =10.65 µm.

8

UNCLASSIFIED/ {fQR OFEICl.t.ls: W81!! 8flti

Page 13

UNCLASSIFIEr,,} POR: OPPIEll<L tt.!I!! 8HL'f
Despite the convenience of the near-field super-lens, (that is, its ability to transport the
image) it still requires an NSOM to read out the image. Within the confines of an
advanced aerospace platform such device (with its necessary auxiliaries) may not fit.
Therefore, one has to consider alternative metamaterials-based ideas for sub-diffraction
imaging. One such idea, the hyper-lens, has been proposed recently by two groups
(References 22-24), and already experimentally tested by another group (Reference
25). The principle of the hyper-lens is very simple: to use an indefinite permittivity
medium (sometimes referred to as the hyperbolic medium because the relationship
between the propagation wavenumbers and the frequency, also known as the constant
frequency contour, has a hyperbolic nature) in a tapered format. Several conceptual
implementations such as the spoke-like structure and the cylindrical multi-layer
structure (see Figure 7, left panel) have been suggested. The hyper-lens works on two
pri ncip les: (a) indefin ite permittivity materials (of which t he super-lens is one example)
are capable of propagating sub-diffraction waves, and (b) the expanding nature of the
hyper-lens can magnify images to the 'A./2 size, at which poi nt they become observable
in a conventiona l microscope . One recent experim ental implementation of the hyper­
lens in UV is shown in t he right panel of Figure 7. The hyper-lens is made of 16 layers
of Ag/ AbOJ. This specific hyper-lens was used for imaging a line pair object with line
width of 35 nm an d spacing of 150 nm and was operat ed at>,., = 400 nm . The magnified
image (350 nm spaci ng) can be cl ea r ly resolved with an opt ica l microscope [n umer ical
aperture (NA) = 1.4], t hus demonstrati ng magnification and proj ection of a sub­
diffraction-limited image into the far fi eld.

Jacob, Alekseyev, Narimanov, Opt.Exp.'06

1

To the fir-field opllCI

1

Salandrino & Engheta, PRB'06

Govyadinov & Podolsky,
PRB'06

Liuet.al, Science'07

Figure 7. Theoretical Concepts (left panel) and Experimental Implementation (right panel) of an Optical
Hyper-lens Capable of Magnifying Sub-Diffraction Objects to Observable (larger than A,/2) Size

9

UNCLASSIFIED/ {EAR OFFICI.IJ.k W81!! tJfltf

Page 14

UNCLASSIFIED/ (FOR OFEICI0k YSE 8Htt
Note that the hyper-lens concept does not require employing a bulky near-field
scanning optical microscope. However, the practical implementation of the hyper-lens is
by no means simple. The original implementation required depositing the sample on the
curved surface of the hyper-lens. A more practical implementation of the super-lens has
been theoretically proposed by another group (Reference 26). The concept is shown in
Figure 8. The hyper-lens involves an array of thin metallic wires converging towards the
tip. As is demonstrated, a dense array of metal wires separated by much less than the
wavelength constitutes a metamaterial with the indefinite perm ittivity tensor.
Specifically, the tensor component along the wires is given by:
(3)

where the z component is along the wires and perpendicular direction is normal to the
wires. Because the only propagating waves are the TEM waves satisfying the
o/ = k; c2 dispersion relation, this meta-medium is strongly anisotropic and supports
sub-wavelength waves which perform imaging. The spatial resolution is given by the
spacing between wires. Figure 8 (right panel) shows the magnified image of a small
('A/25) object placed at the tip of the hyper-lens. The magnification factor is Sx.
5

30-

20.

2

15-

5-.

0
-4 :·

-5-------------------5
0
X!L
5

-1 o __.

0

5
-5

-5

Figures. Hyper-Lens Based on a Converging Array of Metal Wires. A small object can be placed at the tip,
illuminated from the top, and magnified by the expanding array of wires. Left panel : schematic. Right panel: A./25
object magnified by a factor Sx by the expanding hyper-lens. This hyper-lens can operate at mid-IR frequencies .
(Reference 26)

Another concept for sub-wavelength imaging employing metamaterials is the so-called
Far-Field Super-Lens (FSL) . The concept is pioneered in Reference 27. The idea is

10

UNCLASSIFIED/ {EAR OFFICI.IJ.k W81!!! Britt

Text continues in the original file (38 pages).

Previous: DOW-UAP-D140 — AAWSAP DIRD, High-Frequency Gravitational Wave Communications, April 2010 · Next: DOW-UAP-D142 — AAWSAP DIRD, Concepts for Extracting Energy from the Quantum Vacuum, April 2010

Same topic: title & summary match

Same location: Las Vegas, Nevada

Same period: 2010

Same release: Release 06

Same agency: DoW