DOW-UAP-D129 — AAWSAP DIRD, Metallic Spintronics, March 2010
File DOW-UAP-D129 is a declassified pdf from Department of War, recording an incident dated 3/23/10 at Las Vegas, Nevada, published in Release 06 (2026-09-18). This page carries the original file, its official summary and its full text.
- File
- DOW-UAP-D129
- Agency
- Department of War
- Incident date
- 3/23/10
- Location
- Las Vegas, Nevada
- Released in
- Release 06 (2026-09-18)
- File type
Topics: AAWSAP & DIRDs
This document is a Defense Intelligence Reference Document (DIRD), a technical reference format used by the Defense Intelligence Agency (DIA) to capture baseline knowledge on a specific topic for later analytic use. DIRDs are best understood as reference and synthesis products rather than as original research. It is one of 38 DIRDs produced under the Advanced Aerospace Weapon System Applications Program (AAWSAP) between 2009 and 2011. Because AAWSAP’s scope permitted a broad range of supporting topics, not every DIRD in the series directly concerns aerospace systems or future threat assessment. The following summary reflects the DIRD’s scope and framing at the time of writing and should not be read as implying current validation of the concepts discussed.
This DIRD surveys metallic spintronics, a branch of electronics that seeks to use both the electric charge and the magnetic spin of electrons to store, detect, and manipulate information, and argues that the field could lead to faster, lower-power, and more radiation-resistant devices than conventional semiconductor electronics. The report focuses on two main effects: giant magnetoresistance (GMR), which allows magnetic states to be read through changes in electrical resistance, and spin-transfer torque (STT), which allows electrical currents to change those magnetic states. The DIRD reviews their underlying physics, the experimental work then available, and possible applications in memory, sensors, oscillators, and logic devices. The document treats metallic spintronics as a promising field while emphasizing that many of its more advanced proposed applications still require substantial further development.
Open original file · WAR.GOV page
TL;DR
Turns out the only thing spinning in March 2010 was the research agenda.
- DIRD PDF by DoW, March 2010, incident 3/23/10, Las Vegas, NV.
- Surveys metallic spintronics, focusing on giant magnetoresistance and spin-transfer torque applications.
- Concludes field is promising but requires substantial further development.
AI summary
A classified defense document titled "Metallic Spintronics" prepared by the Defense Intelligence Agency's Acquisition Support Division in March 2010. It details research on spintronics, including giant magnetoresistance and spin-transfer-torque, with technical explanations, experimental observations, and applications. The document covers physical principles, deposition methods, and uses in sensors, hard drive read heads, magnetic memory, and high-frequency oscillators. It references studies from 1956 to 2009 and includes discussions on antiferromagnetic spintronics and current-induced effects in magnetic layers.
Full text
Page 2
UNCLASSIFIED//F8R 8FFl&l111L W&& 8f1Ll/
Metallic Spintronics
Prepared by:
Acquisition Support Division (DW0-3)
Defense Warning Office
Directorate for Analysis
Defense Intelligence Agency
Author:
AAP Person 71
Administrative Note
COPYRIGHT WARN ING : Further dissemi nation of the photographs In this publication Is not a.uthorlzed.
This product is one in a series of advanced technology reports produced in FY 2009
under the Defense Intelligence Agency, Defense Warning Office's Advanced Aerospace
Weapon System Applications (AAWSA) Program. Comments or questions pertaining to
I AAWSA Prog ram
this document should be addressed to!AAP Person 1
Manager, Defense Intelligence Agency, ATTN: CLAR/DW0-3, Bldg 6000, Washington,
DC 20340-5100.
ii
UNCLASSIFIED//FQA QFFiGiillk W&& 9tJb¥
Page 3
UNCLASSIFIED/ /FOR OFFIEJIAI:: WSE 0Ptl::1f
Contents
1. Introduction ......................................................................................................iv
2. Giant Magnetoresistance .................................................................................... 1
2.1 GMR Basics .........................................................................................1••········· 1
2.2 GMR Applications ........................................................................................ 3
3. Spin-Transfer-Torque ......................................................................................... 4
3.1 STT Basics ........................................................................................,........... 4
3.2 STT Experiments ............................................................................................... 7
3.3 STT Applications ............................................................................ ..... ........... 10
3.4 STT-Driven Motion of Magnetic Domain Walls ........................................... 12
4, Antiferromagnetic Metal Spintronics ............................................................... 12
4.1 Antiferromagnetic GMR .........,............ .,....................................................... 13
4.2 Antiferromagnetic STT....................................................................... ........ 14
5. Summary and Conclusions ............................................................................... 16
6. References ..............................................................................................,......... 18
Figures
Figure 1. In a Magnetic Multilayer, Several Atomic Layers of Magnetic Material
Alternate With Layers of Nonmagnetic Material ...................................... 1
Figure 2. Resistance of a Magnetic Multilayer R Versus Magnetic Field ...... ............ 2
Figure 3. Differential Resistance dV/dI of a Mechanical Point Contact as a Function
of Current for a Series of Magnetic Fields................................................ 4
Figure 4. Device Schematics for STT Experiments ................................................. 5
Figure 5. Qualitative Picture of STT ....................................................................... 6
Figure 6. Torques on a Magnetic Moment in a Magnetic Field and Subject to an
Electrical Current .........................................................................
7
Figure 7. Spin-Torque-Driven Magnetic Switching .................................................. 8
Figure 8. Oscillatory Voltage .................................................................................. 9
Figure 9. Scanning Transmission X-ray Microscopy Images ................................. 10
Figure 10. Conventional MRAM Cell ....................................................................... 11
Figure 11. Racetrack Memory Concept .................................................................. 12
Figure 12. Schematic of Point Contact to Sample Geometry ................................. 15
, 1• • • • • • • • • • •
iii
UNCLASSIFIED/ /FOA 8FFIGIAI:: WSE OPtl::lf
Page 4
UNCLASSIFIED/ /POK orr1e1At tt!I!! er~LY
Metallic Spintroni·cs
1. Introduction
The rapid pace of progress in the computer industry over the past 40
years has been based on the miniaturization of chips and other
computer components. Further miniaturization, however, faces
serious challenges-for example, increasingly high power dissipation.
To continue on pace, the industry must g,o beyond incremental
improvements and embrace radically new technologies. A promising
nanoscale technology known as spintronics (a neologism for "spin
based electronics"} has emerged. Spintronics refers to the role an
electron spin plays in solid-state physics. Spintronics researchers
aim to develop a revolutionary new class of electronic devices based
on the spin of electrons in addition to the charge. In spintronic
devices, information is carried not by the electron's charge, as in
conventional microchips, but by the electron's intrinsic spin.
Changing the spin of an electron is faster and requires less power
than moving it. Therefore, if a reliable way could be found to control
and manipulate spins, spintronic devices could offer higher data
processing speeds, lower electricity consumption, and many other
advantages over conventional chips, perhaps including the ability to
carry out radically new quantum computations.
Spintronics in ferromagnetic systems is built on a complementary
set of phenomena in which the magnetic configuration of the system
influences its transport properties and vice versa. Giant
magnetoresistance (GMR} (Reference 1, 2} and spin-transfer-torque
(STT} (Reference 3-5} phenomena exemplify such interconnections
in multilayers composed of ferromagnetic (F} and nonmagnetic (N)
layers. The physics and applications of metallic spintronics are
discussed in this report from the perspec:t ive of these two
phenomena. GMR, research on which was awarded the Nobel Prize in
Physics in 2007, refers to a large change in resistance of magnetic
multilayers when the relative orientation of magnetic moments in
their constituent ferromagnetic layers is altered by an applied
magnetic field. The inverse effect, STT, in which a large electrical
current density j can perturb the magnetic state of a multilayer, has
also been predicted (Reference 3, 4} and observed in experiments on
current-induced reversal and precession of magnetization
(Reference 5-9} and magnetic domain wall motion (Reference 10,
11}.
iv
UNCLASSIFIED/ }FOR OFFICiI.ALi !9&i ODIL;¥
Page 5
UNCLASSIFIED/ /&OA QFFI&IAL l:t!II!! er•t I
Spintronics is a broad research field with ( currently) three major
subfields: (1) materials research that is attempting to create new
materials that are both magnetic and semiconductors, (2) research
on novel magnetotransport effects in ferromagnetic metals, and (3)
research on techniques that can be used to manipulate individual
electron spins. The first subfield is targeting magnetic
semiconductors because devices based on such materials would be
the easiest to integrate with the present semiconductor device
technology and processing capabilities. However, despite extensive
research, most semiconductor spintronic devices are still theoretical
concepts awaiting experimental demonstrations. This report focuses
on spintronics research in metallic systems within the scope of the
second and third subfields. The second subfield has experienced an
unprecedented period of new discovery over the past 20 years,
including the discovery of GMR, and has already spawned major
technological change in the information storage industry with the
use of GMR sensors and read heads. The third subfield is vital for
spintronic devices, as virtually any processing of information in such
devices is associated with transport and manipulation of spins.
New and efficient methods for manipulating spins that stimulate
active research programs in spintronics at a large number of
academic institutions and a half-dozen industrial research labs
around the world are highly desirable. The prize to be gained is
active control and manipulation of spin distributions (magnetic
moments) for new and improved functionality in
electronic/spintronic devices. The confluence of intense basic
science and industry interest in ferromagnetic metal spintronics has
not occurred on this scale in physics in a long time.
The report is arranged as follows: Section 2 is dedicated to
magnetotransport effects in magnetic systems where magnetic
configuration can influence the system's transport properties. It
discusses GMR in magnetic multilayers and related phenomena,
highlights basic physical principles responsible for GMR, and
describes technological applications of the effect. Section 3 focuses
on the reverse connection between the system's magnetic
configuration and its transport properties-the so-called STT effect.
The physical origin and potential applications are discussed. Section
4 discusses other new directions in metallic spintronics, with a
particular focus on spintronics with antiferromagnetic materials.
Section 5 summarizes, with an eye to the future, the development of
spintronic technologies and their aerospace applications.
V
UNCLASSIFIED/ /FOR OFFIGIAk Wii SU•k¥
Page 6
UNCLASSIFIED/ /fOlt Offl@IAL ~91! OHL¥
2. Giant Magnetoresistance
2.1 GMR BASICS
This section discusses the phenomenon of giant magnetoresistance (GMR). Excellent
reviews of GMR are available elsewhere (Reference 12-22). The focus on physical
concepts important for the sections to follow are discussed.
GMR in magnetic multilayers refers to a dramatic reduction in the resistance of the
multilayers when subjected to an external magnetic field. GMR's size is usually defined
as the resistance change in magnetic field relative to its peak value. The effect can be
distinguished from the ordinary magnetoresistance (MR) coming from the direct action
of the magnetic field on the electron trajectories via the Lorentz force (Reference 23),
and from the anisotropic MR, which comes from dependence of the resistivity on the
relative orientation of magnetic moment to the current (Reference 24 ).
To prepare the magnetic multilayers,
where several atomic layers of one
(ferromagnetic) material alternate by
layers of another (nonmagnetic)
Current
material (see Figure 1), a wide variety
In
of deposition methods have been used,
the Plane
such as electrochemical deposition
techniques (Reference 25, 26) and
various vacuum deposition techniques
(Reference 27, 28). The latter shares
mainly between two methods using
either sputter deposition or molecular
beam epitaxy (MBE) systems. Sputter
deposition involves knocking off the
Current
atoms of the material of interest from a
Perpendicular
target by particle bombardment,
to the Plane
followed by the deposition of high
energetic atoms ( N2-30 electronvolts
[eV]) onto the substrate. A principal
advantage of sputter deposition is the
ease with which many different
Figure 1. In a Magnetic Multilayer, Several Atomic
materials can be deposited at relatively
Layers of Magnetic Material (shown In grey)
high deposition rates. In contrast,
Alternate With Layers of Nonmagnetic Material
(shown in white). GMR occurs in one of two different
deposition rates in MBE systems are
geometries: (1) when the cu rrent flows in the plane (CIP
usually much lower than for sputtering
geometry) of the layers or (2) wh en th e current flows
systems, but much lower energies
perpendicular (CPP geometry) to t he layers.
(~0.1 eV) of the evaporated material
make this technique favorable for growth of highly oriented single-crystalline films.
The original observation of GMR (Reference 1) was made on MBE grown iron-chromium
(Fe/Cr) mu ltilayers with nearly perfect crystal lin ity. Subsequently, by using sputtered
samples that are grown much more rapidly than MBE samples, it was possible not only
to reproduce these results but also to observe osci ll ations in the magnetoresistance as
the th ickness of the nonmagnetic spacer layers was varied (Reference 29). Subsequent
1
UNCLASSIFIED/ /FOR OFFIGI.t.b W&& &PtblJ
Page 7
UNCLASSIFIED/,'FOA OFFIQI.•.k Wili Qralk¥
studies (Reference 30) on sputtered cobalt-copper (Co/Cu) multilayers revealed
magnetoresistances at room temperatures 3 to 4 times larger than those for iron
chromium and 13 times gr eater than those for the permalloy films that were used as
magnetoresistive sensors in magnetic reading heads at that time. The much higher
numbers observed in magnetic multilayers predetermined the fate of GMR in magnetic
recording technology.
R
The current understanding is that GMR
observed in magnetic multilayers arises
from the dependence of the resistivity
on their internal magnetic configuration
and the role of the external magnetic
field to change this configuration. Figure
2b illustrates GMR in the simple limit
Bs
where the electron mean-free-path is
J
much longer than the layer thicknesses.
RF - - - The electrical transport properties of the
0
system are described in terms of the so
Magnetic Field
called two-current model (Reference
F1 F2
F1 F2
31), based on the suggestion by Mott
(Reference 32) that, at temperatures
lower than the Curie temperature, the
spin -up and spin-down electrons will be
almost independent and carry current in
parallel. Electrons are much more
strongly scattered by a magnetic layer if
t R
R
t R r
t r
r
they and the local magnetization spin in
opposite rather than the same direction
t r
r
R
R
R
(R > r). For simplicity, the figure is
drawn with scattering only at interfaces;
Figure 2. (a) Resistance of a magnetic multilayer R
however, there is also scattering within
versus magnetic field. {b) Origin of GMR in terms of
spin-dependent electron scattering: F1 aInd F2 are
the layers. At zero magnetic field,
ferromagnetic layers with a nonmagnetic layer in
where the magnetizations of adjacent
between. At zero magnetic field, the magnetizations
magnetic layers are aligned
in F1 and F2 are aligned antiparallel (center panel)
and can be switched to parallel orientation by an
antiparallel-for example, because of
applied field. (c) The equivalent resistance circuits
exchange coupling between the layers
corresponding to the three magnetic configurations
(Reference 29)-the spin-down
shown in (b). See text for details.
electrons are weakly scattered in layer
Fl but strongly scattered in F2. In contrast, the spin-up electrons are weakly scattered
in layer F2 but strongly scattered in FL As a result, two channels are equivalent,
leading to a total resistance in this "antiferromagnetic" configuration RAF= (R+r)/2 (see
the corresponding resistance circuit in Figure 2c).
l l
~
' t--
w
ioo}
When the magnetizations of the two F layers are set into parallel configuration by an
applied magnetic field, the spin-up electrons are weakly scattered in both layers and
form a low-resistivity channel, whereas the spin-down electrons are strongly scattered
in all the layers and form a high - resistivity channel. The reversal of magnetic fii eld just
interchanges the roles of spin-up and spin-down channels. The current's shunting by
the low-resistivity channe'I produces a low total resistance RF= 2Rr/(R+ r) in this
"ferromagnetic" configuration . The size of the GMR is defined as (RAF-RF)/RAF = (R-
2
UNCLASSIFIED/ /iiOlil OiiiilCI0L: 1166 ON! X
Page 8
UNCLASSIFIED/ /FOA OFFl&iI.,k Wli& O,.kY
r) 2/(R+r) 2 ~ 1. The other definition ti. R/R = (RAF-RF)/RF= (R-r)2/4Rr (unbounded from
above) is also in use. Figure 2a shows a magnetoresistance curve typical for magnetic
multilayers. The resistance is constant at a minimum value RF above a saturation field
Bs (parallel Fs) and rises to a maximum value RAF as the applied magnetic field B
approaches zero (antiparallel Fs).
GMR occurs in two different geometries (see Figure 1): namely when the current flows
in the plane of the layers, or CIP geometry, or when current flows perpendicular to the
layers, or CPP geometry. Most of experiments on GMR are carried out in the CIP
geometry because measuring the fairly large resistance of a thin film is quite easy (film
length is typically orders of magnitude larger than its thickness). Experiments in the
CPP geometry are more d'i fficult (Reference 33) and require special techniques for
precision measurements of very small resistances ~10-7 - 10-s Q resulting from the
"short and wide" geometry of a 1-mm 2 "wide" and 1-~Lm "long" sample . In order to
increase the resistances to easily observable values, microfabrication techniques can be
used to reduce the sample's cross-sectional area (Reference 34-36). Finally, a simple
and inexpensive point-contact technique (Reference 37) may also be suitable for this
purpose. The samples with a reduced cross-sectional area will be of interest for spin
transfer-torque experiments presented in Section 3.
2.2 GMR APPLICATIONS
GMR is currently used in magnetic field sensors, including those in read heads for
computer hard drives, in galvanic isolators, and in nonvolatile random access memory
devices. Reading information stored on magnetic har d disk drives in computers was the
first large-sca le commercial application of GMR. The information is stored by
magnetizing small regions (magnetic domains) of a magnetic recording disk in different
directions. The stray magnetic fields from these domains are detected by a GMR
sensing element called spin valve. The simplest type of spin valve consists of two
ferromagnetic layers separated by a thin, nonmagnetic spacer. The spin-valve
resistance is smallest when the magnetizations of the two ferromagnetic layers are
para llel and largest when the magnetizations are antiparallel. The antiparallel alignment
is achieved by making the two layers respond differently to an external magnetic field;
an antiferromagnet in contact with one of the layers is used to effectively "pin" the
magnetization in this layer through an effect called "exchange bias." The exceptional
responsiveness of spin valves to magnetic fields has enabled very high areal packing
densities in hard drives.
Other sensor applications using GMR elements include monitoring of a ferrous gear
rotation in machinery oper ation (Reference 38) via detection of a changing magnetic
flux when a gear tooth passes near the sensor, man itoring of electrical current via
detection of the current-induced Oersted magnetic field, and transferring high
frequency signals between isolated circuits (Reference 39) via magnetic fields
generated by a high-frequency inductor in one circuit and replicated in another circuit
by a GMR sensor.
3
UNCLASSIFIED//5O9 AEFICI0L 11 && Q,.L¥
Page 9
UNCLASSIFIED/ /FOA OFFl&ilAk Wlili O,.kY
3 . Spin-Transfer-Torque
This section focuses on the spin-transfer-torque (STT) phenomenon, which refers to a
novel method to control and manipulate magnetic moments in nanostructures by spin
currents-one of the forefront and most exciting areas in magnetism research today.
3.1 STT BASICS
The previous section showed that the magnetic state of a ferromagnet can affect its
electrical transport properties; for instance, the relative orientation of the magnetic
moments in magnetic multilayers underlies the phenomenon of GMR (Reference 1, 2).
The inverse effect, in which a large electrical current density can perturb t he magnetic
state of a multilayer, has also been predicted (Reference 3, 4). Here the current
transfers vector spin between the magnetic layers and induces precession and/or
reversal of the layer magnetizations. Altering the magnetic state with spin currents is
based on quantum mechanical exchange interaction and represents a novel method of
magnetization control on the nanometer length scale and the picosecond time scale.
45 ,---,---,---,---,---,--,,---,--~-,---,---,---,
The first observation of such a spin
transfer phenomenon in magnetic
44
multilayers was recorded by Tsoi et al.
(Reference 5) (see Figure 3). In this
43
experiment, the spin-transfer-induced
excitations were produced by injecting
42
high-density electrical currents into a
Co/Cu magnetic multilayer through a
~
mechanical point contact. Point contacts
~ 41
smaller than 10 nanometers (nm) are
40
formed when a sharpened Cu metal
wire (tip) is carefully brought into
39
contact with the multilayer. The
extremely sma ll cross -sectional area of
38~~~~~-~~~~~~-~
such a contact makes it possible to
0.01
-0.03
-0.02
-0.01
0.00
0.02
0.03
achieve current densities in excess of
10 12 A/m 2 . Because of its extremely
VM
sma ll size ( <10 nm), point contact is a
Figure 3. Differential Resistance dV / di of a
very efficient probe of electrical
Mechanical Point Contact as a Function of Current
for a Series of Magnetic Fields. The peak In dV/dl
transport properties in ext remely small
ind icates the onset of SST excitations. The inset shows
sample volumes inaccessible with other
that t he thres hold cu rrent at t he peak In dV/dl Increases
techniques (for example, electron
linearly with the applied field. (Reference 5)
beam -lithography pattern ing). The
latter qualifies point contact as the smallest probe of STT today.
-a
The STT phenomenon currently attracts considerable attention because it combines
poorly understood fundamental science questions with the promise of applications in a
broad range of technologies. In high-speed, high-density magnetic recording
technology, for instance, SST could replace the Oersted field currently used for writing
magnetic bits in storage media (for example, in magnetic random access memory
[MRAM]). This may lead to a sma ller and faster magnetic memory. Another possible
application is based on the spin -transfer-induced precession of magnetization, which
4
UNCLASSIFIED/ /P'Olt Offl@IAL ~SE 8PtLY
Page 10
UNCLASSIFIED/ /fOft Offl@IAL ~SE 8,.L?f
converts a direct current (de) voltage input into an alternating current (ac) voltage
output. The frequency of such a precession can be tuned from a few gigahertz (GHz) to
> 100 GHz by changing the applied magnetic field and/or de current, effectively
resulting in a current-controlled oscillator for use in practical microwave circuits.
Since its prediction in 1996, the STT effect has been observed in a number of
experiments, including those with mechanical (Reference 5, 9, 40) and lithographic
point contacts (Reference 6, 41), manganite junctions (Reference 7), electrochemically
grown nanowires (Reference 8), lithographically defined nanopillars (Reference 42, 43),
tunnel junctions (Reference 44), and semiconductor structures (Reference 45). These
different methods all share one characteristic feature: they make it possible to attain
extremely high current densities (>10 12 A/m 2 for metallic structures) needed to produce
sufficiently large spin-transfer torques (Reference 3, 4 ). This is achieved by forcing the
electrical current to flow through a very small constriction. The latter can be a
mechanical point contact, a lithographically defined point contact or nanopillar, or a
nanowire, as illustrated in Figure 4. I n all cases, the maximum current density jmax =
I/A is defined by the current I flowing through the device and the minimum cross
sectional area A of the current path. For typical mechanical point contacts, I 1 mA and
A ~100 nm 2 gives jmax ~10 13 A/m 2 . In lithographically defined structures, both I and A
are typically larg er, I ~10 mA and A ~10000 nm that gives jmax ~10 A/m
~
2
12
,
mechanical
point contacts
lithographycal
point contacts
electrodeposited
manganite
nanowires
trilayer junctions
2
.
IIthog raphycal
pillar devices
e-
Figure 4. Device Schematics for STT Experiments. All experiments share one co mmon feature: a small
constriction for electrical current-that Is, point contact, junction, nanowire, or nanopillar. Black (grey) Indicates
insulator; dark blue indicates mag netic materia l.
The basic physical mechanism underlying STT relies on conservation of angular
momentum. Consider a pedagogically simple case where a conduction electron crosses
an interface between a nonmagnetic metal (N) and a ferromagnet (F). We assume the
initial state of the electron's spin S in N is noncollinear to the F's magnetization M. Once
into F, S is subject to an exchange torque caused by M that tends to reorient S.
Therewith, according to Newton 's Third Law, there should also exist a reaction torque
that acts on M - STT torque. Deep into F, S is aligned with M, and the change in
angular momentum that occurs from its reorientation has been transferred to M. Hence
the phenomenon's name: spin -transfer torque. Of course, the torque applied to M by a
single-sp in S is negligibly small owing to S being negligibly small compared with M. For
high current density crossing the N/F interface, however, the number of such spins can
be very large and the resulting effective S might become comparable to M. This
highlights the need for high current densities to observe the STT phenomenon .
A typical experiment on current-driven excitation of a ferromagnet usually involves two
single-domain thin -film magnets separated by a nonmagnetic spacer. Here one magnet
5
UNCLASSIFIED/ ,CFOA QFFIGIAk W&& 0PtLY
Page 11
UNCLASSIFIED/ /FOR OFFIElIAk WSE OPtkY
(Fa) is "hard" and used to polarize the current, while the spacer (N) is thin enough for
the polarized current to get t hrough and excite t he second "free" magnet (Fb) , This
Fa/N/Fb trllayer structure is sim ilar to a GMR spin valve . The GMR effect can thus be
used to monitor the orientation of Fb relative to Fa - GMR varies linearly with cose,
where e is ang le between magnetic moments of Fa and Fb, and a phenomenological
description (Reference 46) gives the trilayer resistance R(0) = RF+ (RAF- RF) (1 cos0)/2. When current flows across Fa/N/Fb, t he current-induced torques act on both Fa
and Fb layers (Reference 3, 47). Th is is schematica lly illustrated in Figure 5. This
qualitative picture of STT .assumes both Fa and Fb layers are perfect spin filters, so t hat
electron spins aligned with t he magnetic moment of, for example, Fa layer are
completely transmitted t hrough the layer, while spi ns aligned antiparallel to the layer
moment are comp letely reflected. When electron current crosses the Fb/N/Fa trilayer
from right to left (Figure Sa), electrons transmitted t hrough Fa will be polarized along
Fa. If spin-diffusion length in N is long enough, this spi n- polarized curre nt will reach Fb
and exert a torque on Fb in a direction so as to align Fb with Fa. Repeating the argument
for Fb, we find that electrons reflected from Fb will be polarized antiparallel to Fb and,
hence, in turn exert a torque on Fa trying to alig n Fa antiparallel with Fb. The net result
is a pinwheel-type motion with both Fa and Fb rotating in the same direction (clockwise
in Figure Sa), as described previously by Slonczewski (Reference 3). When the current
crosses the trilayer from left to right, the directions of the torques are reversed (Figure
Sb) - the torque on Fa is trying to align Fa parallel with Fb, while the torque on Fb is
trying to align Fb antiparallel with Fa .
Fb N
Fa
F N
r V
-¢
¢-
¢
Electron Current
(b)
Electron Current
Figure 5. Qualitative Picture of STT. (a) For left- going electrons magnetic moments (thin arrows) of both Fa and
Fb are rotated clockwi se. (b) For right-going electrons the directions of t he torques (thick arrows) on Fa and Fb are
reversed . (Reference 47)
The above discussion implies the asymmetry of STT with res pect to current direction as
follows. Let's fix t he orientation of the polarizer Fa; in experiments this is usually
accomplished by making Fa very t hick (compared wit h Fb) or by pi nn ing its orientation
with an adjacent antiferromagnetic layer via the phenomenon of exchange bias. If
initially Fb is almost parallel with Fa, t he left-going electrons will stabilize this parallel
alignment, and no STT excitation is present. When current bias is reversed , the torque
on Fb will try to rotate Fb away from Fa and will result in STT excitation of the system.
This asymmetry with respect to current polarity is one of the main features of STT in
experiments; see, for insta nce, Figure 5, where STT excitations are present only at
negative bias.
6
UNCLASSIFIED/ ,'EAR AEFICIOL !9&i Ql'IL¥
Page 12
UNCLASSIFIED/ /FOR OFFl@IAL ~81: 8HLY
3 .2 STT EXPERIMENTS
Section 3.1 introduced the physics of STT in magnetic nanosystems. We have seen that
a high-density electrical current can result in torques on magnetic elements of the
system . These torques may be used to control and manipulate the system's magnetic
state . However, the resulting behavior of the system can differ significantly from case
to case, depending on particular conditions of observation. For instance, in modest
external magnetic fields, magnetization of a small element can be repeatedly reversed
between two stable configurations, while at higher fields, where the reversal is
energetically unfavorable, the moment can be set into precession at a very high
...
frequency . To understand details of what happens with a magnetic moment S in a
particular situation, one can use Newton's Second Law.
...
...
For S this would be the Landau-Lifshitz-Gilbert equation, where the rate of change of S
...
is set equal to the net torque acting on S :
Equation 1:
...
Here the first term on the right is the
torque on a magnetic moment S in an
~
effective magnetic field B eff, (including
applied, demagnetizing, anisotropy, and
other fields), with y the gyromagnetic
ratio; the second term is a
phenomenological damping term
introduced by Gilbert, with a. the Gilbert
damping parameter; ~e thir~ term is
the SST where small s· and * are unit
•
STT
•
Damping
vectors along and the polarizer ' *, I
is the current, µs is the Bohr magneton,
e is the electron charge, and 11 is the
spin -polarization factor.
The diagram in Figu re 6 shows the
directions of the three torques from
Equation 1. Note that, depending on the
polarity of applied current, the STT
Figure 6. liorques on a Magnetic Moment in a
torque can be either in the same or
Magnetic Field and Subject to an Electrical Current
Previous: DOW-UAP-D128 — AAWSAP DIRD, Anomalous Acute and Subacute Field Effects on Human Biological Tissues, March 2010 · Next: DOW-UAP-D130 — AAWSAP DIRD, Technological Approaches to Controlling External Devices, March 2010
Same topic: title & summary match
Same location: Las Vegas, Nevada
- DOW-UAP-D174 — Utah Ranch Investigation Report, April 2010
- DOW-UAP-D166 — MUFON Reports Prepared for BAASS, November 2008
- DOW-UAP-D168 — BAASS Project Management Plan, December 2008
- DOW-UAP-D169 — BAASS Monthly Report, March 2009
- DOW-UAP-D170 — BAASS Monthly Report, April 2009
- DOW-UAP-D171 — BAASS Monthly Report, June 2009
Same period: 2010
- DOW-UAP-D114 — AAWSAP Contract Modification P00003, May 2010
- DOW-UAP-D113 — AAWSAP Contract Modification P00002, February 2010
- DOW-UAP-D115 — AAWSAP Contract Modification P00004, May 2010
- DOW-UAP-D116 — AAWSAP Contract Modification P00005, September 2010
- DOW-UAP-D133 — AAWSAP DIRD, The Space Communication Implications of Quantum Entanglement and Nonlocality, March 2010
- DOW-UAP-D134 — AAWSAP DIRD, Maverick Inventor Versus Corporate Inventor: Where Will the Next Major Innovations Arise, March 2010
Same release: Release 06
- DOW-UAP-PR159 — Historical Film of Reported UFOs, Utah, 1952
- LLE-UAP-PR001 — Unresolved UAP Report, Colorado, 2023
- LLE-UAP-PR002 — Unresolved UAP Report, Colorado, October 2023
- DOW-UAP-PR133 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR135 — Unresolved UAP Report, Middle East, 2025
- DOW-UAP-PR140 — Unresolved UAP Report, Middle East, 2022
Same agency: DoW
- DOW-UAP-D094 — Analysis of Flying Object Incidents in the United States, 1949
- DOW-UAP-D097 — Project Sign Progress Report, 1948
- DOW-UAP-D084 — US Army-Flying-Saucer-Study 1949
- DOW-UAP-D155 — Air Intelligence Information Report, Saudi Arabia, 1957
- DOW-UAP-D176 — Triangular UAP AARO Memorandum for Record, 2026
- DOW-UAP-D177 — Unresolved UAP Report, Catalina Island, 1955