AARO Satellite Flaring Paper 508 FINAL 04222025
File AARO-AARO_Satellite_Flaring_Paper_508_FINAL_04222025 is a declassified pdf from AARO. This page carries the original file, its official summary and its full text.
- File
- AARO-AARO_Satellite_Flaring_Paper_508_FINAL_04222025
- Agency
- AARO
- File type
Open original file · AARO.MIL page
TL;DR
April 22 2025: even the satellites were flashing more than the fire alarm.
- AARO Satellite Flaring Paper 508 FINAL 04222025, AARO, 22 Apr 2025, PDF
- Starlink satellites produce bright diffuse/specular flashes, misidentified as UAP; includes 2022 Gallup, NM case
- No official conclusion in the file
AI summary
A technical paper titled "AARO Satellite Flaring Paper 508 FINAL 04222025" was authored by J. E. A. Zhang, NOAA, and others, dated April 22, 2025. It discusses satellite flaring, focusing on Starlink satellites and how their reflections of sunlight can create bright flashes mistaken for unidentified aerial phenomena. The document explains the geometry of flares, provides calculation methods, and includes observational examples from 2022 and 2024.
Full text
Page 1
All-domain Anomaly Resolution Office (AARO)
An AARO Information Paper
Correlations of Starlink 1 Satellite Flaring with UAP
Observations
December 2024
Introduction
With the advent of satellite communication mega-constellations including the SpaceX Starlink,
Eutelsat OneWeb, Amazon Kuiper, and Chinese G60 constellations, there are currently thousands
of artificial satellites in Low Earth Orbit (LEO) 2 and tens of thousands more planned for launch
over the next decade [1]. Satellite flaring is an optical phenomenon which occurs when sunlight
reflects off a satellite's surfaces, such as antennas or solar panels. This paper discusses specular
and diffuse reflection of sunlight from man-made satellites and how these effects can be interpreted
as unidentified anomalous phenomena (UAP). It also provides a method for observers to determine
whether observations may be attributable to satellite flaring.
Background
Using reflected sunlight from man-made satellites to observe and track their movement goes back
to the earliest days of space exploration [2]. As noted above, several companies develop and launch
mega-constellations, providing internet access to most of the globe. Currently, there are nearly
10,000 artificial satellites in LEO and this number is expected to grow several-fold over the next
decade [1]. Figure 1 illustrates the location of Starlink satellites in orbit as of December 2, 2024,
at 11:00 AM Eastern Standard Time. As of the end of November 2024, there were over 6,700
Starlink satellites in orbit.
Figure 2 illustrates the concepts of diffuse and specular reflections, which describe how light
bounces off objects. Figure 3 shows how sunlight reflected in these two ways is directed toward
an observer on the surface of the Earth. As seen in the left side of Figure 2, diffuse reflection occurs
when light reflects from a rough or irregular surface. Light impinging upon a rough surface reflects
in many directions, which spreads the light over a large range of angles from the reflecting surface,
as illustrated by the gray colored "light cone” in the Figure 3(a). From a single observation point,
this cone of light can be visible for up to several minutes as the satellite moves in its orbit across
the sky. Additionally, the intensity of reflected light significantly decreases the further away the
observer is from the reflecting surface. At the Earth’s surface, the intensity of diffusely reflected
light from a satellite in LEO will typically have diminished to the point that the brightness is
Any reference to a non-federal entity is for informational purposes only and does not constitute an express or implied
endorsement of any commercial service, from AARO, the Department of Defense, or the Executive Branch. This
report focuses on Starlink satellites, but its principles are applicable for any analogous satellite constellation.
2
Altitude for Low Earth Orbit (LEO) ranges from 300km to 2,000km.
1
1
Page 2
All-domain Anomaly Resolution Office (AARO)
comparable to starlight. Due to their construction and orientation, many man-made satellites in
LEO diffusely reflect sunlight and can appear as stars that move across the night sky.
Figure 1: Graphic of Starlink satellites in orbit. Ref: https://www.heavensabove.com/StarLink.aspx
Specular reflection, also known as glint, occurs from a very smooth, mirror-like surface as
illustrated on the right side of Figure 2. Unlike diffusely reflected light, the light striking a smooth
surface reflects light at the same, or nearly the same, angle as the incident light. Therefore, the
reflected light cone from a satellite in LEO is much narrower for specular reflection as compared
to diffuse reflection, as illustrated in Figure 3(b). This dramatically increases its observed
brightness by several orders of magnitude, but greatly decreases its observation time as the cone
passes over the observer.
Figure 2: Image illustrating the difference between diffuse reflection (left) and specular
reflection (right).
2
Page 3
All-domain Anomaly Resolution Office (AARO)
These very bright, short lived flashes of light are called “satellite flares” or “satellite glint.” The
design, launch, and operation of SpaceX Starlink mega-constellations has led to a significant
increase in the sighting of satellite flares, dubbed “Starlink flares,” noted by scientists and nonscientists alike.
Figure 3: Illustration of (a) diffuse reflection of sunlight from a satellite and (b) specular
reflection of sunlight from a satellite as viewed by an observer on the surface of the Earth.
Satellite Flares and Satellite Trains
Figure 4 shows a Starlink satellite in its operational configuration. Starlink satellites’ unique design
and orientation make them susceptible to both diffuse and specular reflection, which causes their
high visibility in the night sky. There are two key components to most satellites: (i) the solar panel,
and (ii) the satellite bus. The solar panel provides a power source for the satellite bus. The bus is
the primary body of the satellite that contains the electronics and systems to perform its designated
mission. The Starlink bus has multiple mirrored panels and flat antenna arrays on the bottom side
of the bus that faces the Earth in its operational configuration. Dependent on the generation of the
Starlink satellite, the reverse side of the large solar panel can be a very efficient diffuse reflector,
while the satellite bus is a very efficient specular reflector [3].
The phenomenon of satellite flaring is not new. This was well documented in the late 1990s and
early 2000s after the launch of the Iridium satellite constellation [4]. However, satellite trains, or
“Starlink trains,” are relatively new and result from the launch process SpaceX uses, which deploys
3
Page 4
All-domain Anomaly Resolution Office (AARO)
dozens of small satellites during a single launch event. Immediately following a launch, and for
several days afterward, these satellites form a distinctive line of bright objects before fading as
they ascend to their final orbital positions. Figure 5 below provides examples of each flare
scenario.
satellite bus
solar panel array
Figure 4: Rendering of Starlink satellite noting the satellite's bus and solar panel components.
Adapted from [5].
Starlink satellites transition through three orbital phases on their way to their final orbit, with each
phase creating a different visual phenomenology to ground observers. During the launch phase,
dozens of satellites, with their solar panels folded, are loaded in large groups on the rocket delivery
vehicle. Once the delivery vehicle arrives to an initial position in LEO, the satellites separate and
unfold their solar panels.
(a) (b)
Starlink Flare
Sidney, NE
Figure 5: (a) photo of a string of Starlink satellites called "Starlink trains " not long after launch
on 29 August 2022 [6]; and (b) photo taken by AARO personnel of a satellite flare at peak
intensity for a Starlink satellite, which illustrates how much brighter Starlink flares can be than
surrounding stars. Photo taken before sunrise on March 11, 2024 near Sidney, Nebraska.
Camera settings: [7]
4
Page 5
All-domain Anomaly Resolution Office (AARO)
After the satellites have separated and traversed a specific distance from one another, they enter
the second phase known as orbital raise. During this phase, the satellites navigate from their initial
low orbit to their final orbital altitude, which is nominally 550km for the current generation of
Starlink satellites. During the ascent, drag arises due to skin friction along the satellites' surfaces.
To reduce the effects of drag, the satellites orient into a streamlined profile by shifting their solar
panels parallel to the Earth, see Figure 6(a). It's this phase that creates the satellite trains, as light
reflects off each solar panel of the ascending satellites. In the third phase, the satellites reach their
final position called their operational altitude. Here the satellites reorient to their operational
configuration with each satellite bus and its mirrored panels facing the ground and their solar
panels extended above to maximize capture of sunlight.
It is this operational orientation of the satellites, Figure 6(b), that leads to flares or glint when the
geometry of the Sun, satellite, and observer are properly aligned. These flares are orders of
magnitude brighter than starlight and appear in a small section of sky called the "flare window." It
is possible to have simultaneous flares from multiple satellites moving in differing orbits. To an
observer on the ground, simultaneous flares might appear to be spinning lights, small glowing orbs
that disappear and reappear, or tracing out geometric shapes such as triangles, or other odd
morphologies that move quickly across this small section of the sky. To demonstrate how bright
satellites can appear from the ground, AARO personnel photographed Starlink flaring on March
11, 2024, near Sidney, Nebraska (NE). These photographs are shown in Figure 7 and Figure 8.
These images were taken using a 10 second exposure time which makes them appear as short
streaks in the images versus point sources.
(a) (b)
OPEN BOOK
SHARK-FIN
Figure 6: (a) rendering of Starlink satellite in its configuration during orbital raise; and (b)
rendering of Starlink satellite in its final operational orbit. Adapted from [8].
Estimating When and Where to See Starlink Flares
The location and appearance of these flares is a function of the satellite's location, the Sun's
position, the time, the date, and the observer's latitude. Many in the astronomy community are
concerned about the light pollution created by satellite flares from these mega-constellations and
their negative impact on scientific studies as well as the risks posed to the access and safety of
space [9] [10] [11] [12]. This has driven some groups to create software models that predict the
brightness of satellites based on their astronomical locations. Despite this, few publications exist
5
Page 6
All-domain Anomaly Resolution Office (AARO)
that discuss how to the predict the azimuth and elevation angles of satellite flares to assist a ground-
based observer. The key to performing this prediction is to understand the position of the sun
relative to the satellite and the observer.
Starlink Flare
Sidney, NE
Figure 7: Image of Starlink flare taken by AARO personnel before sunrise on March 11, 2024
near Sidney, NE. Image was taken using a 10 second exposure time which led to the Starlink
flare appearing as a streak instead of a point source. [7]
Several Starlink Flares
Sidney, NE
Figure 8: Image of multiple Starlink flares taken by AARO personnel before sunrise on March
11, 2024 near Sidney, NE. Image was taken using a 10 second exposure time which led to the
Starlink flares appearing as streaks instead of point sources. [7]
The Sun's position in the sky can be described using two measurements: (i) the Sun's altitude
angle, and (i) the Sun's azimuth angle. The Sun's altitude, or solar altitude, is the angle between
6
Page 7
All-domain Anomaly Resolution Office (AARO)
the Sun and the Earth’s surface at the horizon as viewed from an observer’s position on the earth.
During the day, solar altitude is a positive number expressed in degrees above the horizon. Solar
altitude is negative at night, expressed in degrees below the horizon. Solar azimuth describes the
angle to the Sun as referenced from true North at the observer’s position, e.g., 90° being due East
and 270° being due West. Seasonal changes affect the measurement of solar azimuth because of
the Earth's 23.5° axial tilt. In the northern hemisphere, the Sun appears to rise and set further north
each day between the winter and summer solstices. After the summer solstice, this cycle reverses,
and the Sun rises and sets further south each day until the winter solstice. Thus, the specific
azimuths of the rising and setting Sun are also dependent on the observer’s latitude [13]. There are
many online resources that will calculate the Sun’s altitude and azimuth at a given time and date
for a specific observer’s location expressed in latitude and longitude [14] [15]. Similarly, the
satellite’s altitude with respect to an observer’s position can be represented by an angle above the
horizon. This look angle is the elevation angle from the horizon to the observation point in the sky,
i.e., the point in the sky to potentially see flares. These geometries are shown in Figure 9.
The following calculations provide a guide to help observers predict when and where they might
be able to view a satellite flare in the night sky. This is an approximate mathematical treatment
and meant to be a guideline good to within a few degrees to help the observer estimate the look
angles and times for Starlink flares.
Figure 9: Cartoon of Sun’s altitude and azimuth as referenced to the location of an observer on
the Earth. Also defined is the look angle to observation point in the sky.
Using equations (11), (1) and (5) in reference [16], we can calculate the look angle to the satellite,
e, as a function of the Sun’s altitude, 𝑎𝑎.
𝜋𝜋
𝑎𝑎(𝜀𝜀) = − 𝜀𝜀 − sin−1 �
2
𝑅𝑅𝐸𝐸
𝑅𝑅𝐸𝐸 +ℎ
𝜋𝜋
sin � − 𝜀𝜀�� + cos −1 �
2
𝑅𝑅𝐸𝐸
𝑅𝑅𝐸𝐸 +ℎ
�,
(1)
7
Page 8
All-domain Anomaly Resolution Office (AARO)
where ℎ is satellite height above the Earth’s surface, 𝑅𝑅𝐸𝐸 is the Earth’s radius. As the zenith angle
𝜋𝜋
is complementary angle of the look angle, 𝜀𝜀, the substitution 𝑧𝑧 = − 𝜀𝜀 has been made in Equation
(1).
2
Equation (1) is a transcendental equation, meaning that it must be solved numerically to find ε as
a function of 𝑎𝑎, the sun’s altitude. Using the mathematical software package MATLAB®, a plot
was generated and is shown in Figure 10 for various Starlink satellite constellations, each of which
have varying orbital altitudes between about 540km and 570km.
Figure 11 illustrates the geometry for a nominal Starlink orbital altitude of 550km. Simple
trigonometry is used to determine that θr ≅ θi ≅ 67° and the angle A ≡ |a| + ε ≅ 46°. For
perfect specular reflection and a satellite bus with its bottom surface that is aligned exactly
perpendicular to its orbit, A = 46° and ε = 0. In other words, the satellite and resultant flare are
directly at the horizon. Realistically, no surface is a perfect specular reflector and any small
deviations from exactly perpendicular will reflect light off-axis resulting in ε ≠ 0. Assuming the
light cone is reflected as much as ± 2° off axis, Starlink flares are then generally visible when the
Sun’s altitude is roughly between -38° and -46° as illustrated in Figure 10. This is determined from
the inset in Figure 10, which shows that flares are visible somewhere between the horizon and
about 10° above the horizon for up to 2° off axis reflection, as indicated by the dashed green lines.
Figure 10: Plot of the Elevation Look Angle from the horizon to the satellite flare window as a
function of the Sun’s altitude below the horizon. Green lines indicate best set of Elevation Look
Angles for observing Starlink flares is up to about 10° above the horizon assuming off-axis
reflections up to 2°.
8
Page 9
All-domain Anomaly Resolution Office (AARO)
Figure 11: Graphic illustrating the geometry discussed above. The horizon is indicated by the
dashed arrow. ε is the angle above the horizon to the position of the satellite and potential flare.
These numbers will vary for satellites with different orbital altitudes, but these guidelines are
suitable for the current family of Starlink satellites.
Step-by-step Process to Estimate Location of Flare Window
We now have enough information needed to estimate the look angles to observe Starlink flares,
specifically the sun’s elevation angle and satellite elevation angle. One can use the following
process to predict the flare window’s azimuth and elevation. Table 1 provides a template for
recording your observation.
Note the following information:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Choose the observation location (latitude and longitude).
Select the year.
Select the date.
Predict the Sun's azimuth at the chosen time, date, and location by entering the information
from steps 1-3 into an online calculator of your choice. Two example calculators are
https://www.suncalc.org/ or https://www.timeanddate.com/sun.
Use the slider bar at the top of the page for suncalc.org or the expandable tables on
timeanddate.com to find the time and azimuth after sunset when the Sun's altitude is -38°.
Record the Sun's azimuth and the local time of day.
After recording information from step 6, use the slider bar at the top of the page for
suncalc.org or the expandable tables on timeanddate.com to find the time and azimuth after
sunset when the Sun's altitude is -46°.
Record the Sun's azimuth and the local time.
Repeat steps 4 through 8 for the following day. Find the times and azimuths for the Sun
before sunrise at -38° and -46°.
9
Page 10
All-domain Anomaly Resolution Office (AARO)
10. Using the information in the table, perform the observations and record the measured
values in the table.
Table 1: Example template for recording estimated azimuth and times for Starlink flare windows.
Observation Site
Latitude
Longitude
Date
Time (L)
After sunset
Sun Altitude
NOTES:
-38°
Look
Angle
10°
-46°
0°
Measured Values of Satellite Flare
Date
Time (L)
Azimuth
Flare
Azimuth
Flare
Elevation
Date
Time (L)
Before sunrise
Sun Altitude Azimuth
-46°
Look
Angle
0°
-38°
10°
Measured Values of Satellite Flare
Date
Time (L)
Flare
Azimuth
Flare
Elevation
The scenario below illustrates this process by working through an example.
Scenario
Suppose AARO personnel want to gather images and video of Starlink flares to support the
development of this information paper. AARO personnel travel from March 8-12, 2024, and select
Sidney, NE as the destination. This is due to its ~4000 feet altitude within the High Plains and the
generally flat terrain in this area, both of which make conditions more favorable to observe spacebased objects near the horizon.
The necessary information is:
1. Observation location: Sidney, NE
2. Year: 2024
3. Day: March 10 after sunset and March 11 before sunrise
For steps 4 through 10, see Table 2 below. This was completed using https://www.suncalc.org.
Table 2 shows that the measured azimuths and altitudes of the exemplified flares fall within the
predicted values. Figure 12 and Figure 13 are example photos taken during the two timeframes
noted in Table 2. AARO used https://theskylive.com/planetarium to reference the flare locations
against the known positions of other celestial bodies, which are noted in the images.
Implications for Airborne Observation
Up to this point, the discussion has assumed the observer is located on the surface of the Earth.
However, the phenomena of satellite trains and flares are also visible from aircraft. The angles,
geometries, etc. may differ, but the fundamental principles are the same. For an airborne observer,
the opportunity to see flares can persist longer when flying East to West after sunset in the direction
of the Sun or West to East before sunrise in the direction of the Sun because they can stay in the
flare light cone longer.
10
Page 11
All-domain Anomaly Resolution Office (AARO)
Table 2: Example table completed for the scenario described above.
Observation Site Latitude 41.0064°
Sidney, NE Longitude -103.1260°
NOTES:
After sunset Before sunrise
Date Time (L) Sun Azimuth Look Date Time (L) Sun Azimuth Look
Altitude Angle Altitude Angle
03/10/24 10:22PM -38° 305.2° 10° 03/11/24 2:44AM -46° 38.1° 0°
11:20PM -46° 321.6° 0° 3:43AM -38° 54.7° 10°
Measured Values of Satellite Flare Measured Values of Satellite Flare
Date Time (L) Flare Flare Date Time (L) Flare Flare
Azimuth Elevation Azimuth Elevation
03/10/24 10:38PM 309.6° 3.2° 03/11/24 3:13AM 47.4° 3.7°
March 10, 2024 @ ~ 10:38PM
Alcyone @ ~282
azimuth,~23.8° altitude
α Cas @ ~332° azimuth,
~17.7° altitude
Jupiter @ ~284.5°
azimuth, ~5.9° altitude
Starlink flare @ ~309.6
azimuth, ~3.2° altitude
Figure 12: Images taken by AARO personnel near Sidney, NE after sunset on March 10, 2024.
Note that the azimuth to the Starlink flares falls within the predicted angles in Table 2 at the time
of image capture. Camera settings: [7].
11
Page 12
All-domain Anomaly Resolution Office (AARO)
March 11, 2024 @ ~ 3:13AM
Vega (α-Lyr) @ ~65.9°
azimuth, ~34.6° altitude
α-Cep @ ~27.6° azimuth,
~25.8° altitude
Deneb (α-Cyg) @ ~45.6°
azimuth, ~18.8° altitude
ε-Cyg @ ~53.8° azimuth,
~10.7° altitude
Starlink flare @ ~47.4°
azimuth, ~3.7 ° altitude
Figure 13: Images taken by AARO personnel near Sidney, NE before sunrise on 11-MAR 2024.
Note that the azimuth to the Starlink flares falls within the predicted angles in Table 2 at the time
of image capture. Camera settings: [7].
Figure 14 shows the geometry of an airborne observer and two ground-based observers. The
altitude of an airborne observer extends the Line-of-Sight (LOS) distance to the horizon as
compared to a ground-based observer at the same latitude and longitude location, O1. For the
airborne observer, this is equivalent to shifting their observation point by a distance d (the arc
length) to align with a ground-based observer at position O2.
horizon RLS
-
02
EARTH \
hALT
RE - - - O^
RLos= line-of-sight distance to horizon
from airborne observer
R= radius of the Earth, nominally 6371
km
h = altitude of airborne observer
d = ground distance between
observation points O and O2
θ is the central angle between
observation points O1 and O2
12
Page 13
All-domain Anomaly Resolution Office (AARO)
Figure 14: Diagram illustrating that an airborne observer at position O1, shares the same
observation horizon as a ground-based observer at position O2. d is the projected shift of the
observation horizon for the airborne observer.
The LOS distance can be found using the Pythagorean theorem as:
which simplifies to:
Since ℎ𝐴𝐴𝐴𝐴𝐴𝐴 ≪ 𝑅𝑅𝐸𝐸 , then
𝑅𝑅𝐿𝐿𝐿𝐿𝐿𝐿 = �(𝑅𝑅𝐸𝐸 + ℎ𝐴𝐴𝐴𝐴𝐴𝐴 )2 − 𝑅𝑅𝐸𝐸2
(2)
2
𝑅𝑅𝐿𝐿𝐿𝐿𝐿𝐿 = �2𝑅𝑅𝐸𝐸 ℎ𝐴𝐴𝐴𝐴𝐴𝐴 + ℎ𝐴𝐴𝐴𝐴𝐴𝐴
.
(3)
𝑑𝑑 ≈ 𝑅𝑅𝐿𝐿𝐿𝐿𝐿𝐿 .
(4)
This relationship is plotted in Figure 15.
Figure 15: Projected shift in observation horizon (O1 to O2) as a function of observer altitude.
The latitude and longitude at position O2 (the new effective observation point for the airborne
observer) can be then estimated using the Haversine formula [17]. There are online calculators
available to find the terminal coordinates when given a starting point, bearing and range, e.g.,
https://www.fcc.gov/media/radio/find-terminal-coordinates. Alternatively, one could use the ruler
tool in Google Earth to estimate the terminal coordinates.
13
Page 14
All-domain Anomaly Resolution Office (AARO)
The coordinates for O2 are used to determine the Sun’s altitude and the observer’s elevation look
angle to potentially see flares for a given day, time, airborne observer location, and aircraft bearing
(or azimuth look angle as noted in Footnote 3).
Unlike the ground-based observation case discussed above, an airborne observer does not have the
ability to “park themselves” at a given location and wait for the Starlink flaring window to come
into view. Consequently, the process described below is more likely useful to determine whether
a previous sighting phenomenon may have been the result of Starlink flares.
Below is the process for determining the elevation and azimuth look angles for an airborne
observer to determine whether their sighting may potentially have been due to Starlink flares. Table
3 is an example template that may be useful.
1. Choose the observation location (latitude and longitude, O1), altitude and aircraft bearing
for the airborne observer (or azimuth look angle as noted in Footnote 3).
2. Use Figure 15 and online resources or Google Earth to calculate the effective observation
location, O2, for the airborne observer. Note the effective latitude and longitude in Table 3.
3. Select the year of the observation.
4. Select the calendar day of the observation.
5. Select the local time of the observation.
6. Determine the Sun's azimuth for the given time, date, and year at the effective observation
position O2. If O1 and O2 are not in the same time zone, use the time zone for O1 when
converting from local time to UTC.
7. Go to the online Sun altitude and azimuth calculator of your choice, e.g.,
https://www.suncalc.org/ or https://www.timeanddate.com/sun, and enter the information
from steps (2) through (5).
8. Use the slider bar at the top of the page for suncalc.org or the expandable tables on
timeanddate.com to find the Sun’s azimuth for the given local time of the observation and
record this into the appropriate blocks in the table.
9. Use Figure 10 above to estimate the elevation look angle at which Starlink flares should
have been visible and record this information into the table.
10. Compare the Sun’s azimuth and elevation look angle for the estimated flare window to the
sighting’s azimuth and elevation to determine if Starlink flares may be a likely explanation
for the observed phenomena.
Case
AARO received a Federal Aviation Administration UAP report from an airline pilot describing
multiple unidentified lights moving in different directions. The report states that the pilot was
traveling eastbound near Gallup, NM (35.5224°N, 108.7235°W) on October 9, 2022, at
approximately 3:50AM local time. The aircraft was at an altitude of 35,000 feet and had a bearing
It is implied that the airborne observer is looking forward out of the aircraft cockpit, i.e., a pilot, thus, the aircraft
bearing and azimuth look angle are approximately in the same direction. If the observer were a passenger looking out
of a side window, then replace the aircraft bearing with the azimuth look angle of the observer as measured from true
North to project O1 to O2.
3
14
Page 15
All-domain Anomaly Resolution Office (AARO)
(heading) of approx. 70° from true North. The pilot noted that the UAP were “multiple lights
moving in different directions, left of the constellation Leo.” No further data was provided.
The following procedure will determine if the reported lights could be Starlink flares.
Table 3: Example template for recording estimated azimuth and elevation for Starlink flares that
could explain the UAP sighting for an airborne observer.
Observation Site
Latitude, O1
Longitude, O1
Aircraft Altitude
Aircraft Bearing
Effective Obs. Site
Date
Latitude, O2
Longitude, O2
Time (L)
Sun Altitude
Sighting Parameters
Sun Azimuth
Look Angle (Figure 10)
Sighting Azimuth
Sighting Elevation
The necessary information is then:
1) Observation location, O1: 35.5224°N, 108.7235°W
Altitude: 35,000 feet
Aircraft Bearing (also assumed to be observer's azimuth look angle): 70°
2) Using https://www.fcc.gov/media/radio/find-terminal-coordinates:
The effective observation location, O2 is: 36.5987°N, 104.8259°W or near Cimarron, NM
3) Year: 2022
4) Date: October 9
5) Time: 3:50AM local
For steps 6 through 8, see completed Table 4 below. This was completed using www.suncalc.org.
Table 4: Example table completed for the airborne scenario described above.
Observation Site
Effective Obs. Site
Latitude, O1
Longitude, O1
35.5224°
Aircraft Altitude
35,000 feet
Aircraft Bearing
70°
-108.7235°
Latitude, O2
36.5987°
Longitude, O2
-104.8259°
Sun Azimuth
Date
Time (L)
Sun Altitude
10/09/22
3:50AM
-38.5°
65.6°
Look Angle (Figure 10)
~9° above the horizon
15
Page 16
All-domain Anomaly Resolution Office (AARO)
Sighting Azimuth Sighting Elevation
Sighting Parameters:
~63.3° ~5.7°
The specific azimuth and elevations of the sighting were not given, but the pilot does state that the
UAP was to the "left of the constellation Leo." Therefore, it is possible to approximate the sighting
parameters by determining the Leo constellation's location at the given day and time when viewed
from the effective observation location, O2. Figure 16 below was generated using the planetarium
view on the website https://in-the-sky.org/satmap planetarium.php?. Noted in the image is
information on several stars that provide a reference for estimating the sighting azimuth and
elevation location "left of the constellation Leo." Also shown are numerous Starlink satellites that
were present in the sky during this time. The red satellites are estimated to be flaring per this
website. The red arrows were added to the image by the author to show the direction of motion for
several of the Starlink satellites. Note their crossing directions, which are consistent with the pilot's
report of "multiple lights moving in different directions." The azimuth and elevation of the stars
was determined using the website https://theskylive.com/planetarium?.
The estimated area of the sky the pilot likely referenced is circled by a white, dashed oval shape
and the approximate center of this area is provided in the image. Using this estimate, it is possible
to determine the sighting parameters required in Table 4. Comparing these to the expected location
of the Starlink flare window for this date, time, and location (given by the Sun's azimuth and look
angle in the table), it is seen that these are very comparable. Consequently, the anomalous lights
reported by the pilot are very likely Starlink and other satellite flares.
Field of view: 1° 1.25° 1.5° 2 2.50 3 4 5° 6° 8 10° 12 15° 20 25° 30 40° 50° 60° 75 90° 120 150 180
Gemini
Center of approx. sighting:
63.3° azimuth,5.7° elevation STARLINK-3734'
Monoceros
STARDINK-1552 ONEWEB-0130
ONEWEB:0136 GPS 19 ONEWEB-0297 Canis Minor •STARLINK-2162
Canis Major
v-UMa @ 53.5° azimuth, 6.9° elevation Cancer STARLINK-1470
Ursa Major ONEWEB-0131
STARLINK-2753
Leo Minor
STARLINK-2659 y01-Leo @ 72.2°azimuth, 9.3° elevation GPS 28
STARLINK-4174 STARLINK-4056 STARLINK-1334 EWEB-01
FARLINK-4254
INK-1564
4106 STARLINK-246 STAFARNKN 5047 STARLINR-3814'TARLINK-2545
Puppis
WEB-0298 EWEBrO295K-2689 FARLIN
STARLINK500 EB-0293 Ceres @ 72.6° azimuth, 4.7° elevation
SMRLINK-2667 STARLINK-2629
-1260 TARLINK-4051 GENEWENK4394 IRIDIUI
RLINK-3294 STARLINK-4129